Align Torque Tube Rear Drive Gear Set

Use for T-REX 550/600 class.

Requirements:
Tail rotor shaft assembly x 1
Long umbrella equipment x 1

This item is often purchased with the above pointed out item.

M0.8 Torque Tube Front Drive Gear Set/34T

Use for T-REX 600PRO/600EFL PRO/550E

Specifications:
600PRO Front drive equipment assembly x 1
600PRO Short umbrella equipment x 1
600PRO Long umbrella equipment x 1

This item compliments the main item below.

Torque Tube

Use for T-REX 550E.

Requirements:
Torque tube x 1
Bearing MR148ZZ x 1(Φ8xΦ14x4mm)

Lots of others have actually purchased this item together with the item that you are presently checking out.

Torque Tube Front Drive Gear Set

This is a replacement torque tube front drive equipment for the Align T-REX 550, 600 and 600N line of helicopters utilizing the optional torque tube upgrade. Suches as one front drive equipment assembly and one 20t 21.2x33.6mm front umbrella gear.

Note: In order to use this torque tube drive equipment set on a T-REX 550, the helicopter should be geared up with the straight-cut equipment setup. To figure out if your helicopter utilizes inclined gears or straight-cut gears, observe the main drive equipment which will either have inclined or straight-cut teeth. 



Lots of others have actually purchased this item together with the item that you are presently checking out.

Tail Boom (Black)

Requirements:
Tail boom x 2(Φ20xΦ21.5x625mm)
Tail control guide x 2
Rudder control rod(B) x 1(Φ2x657mm)
Boll link x 2

Want an additional great item to match the above pointed out item?

Cnc Slant Thread Main Drive Gear/ 112T

Use for T-REX 550E.
Must with CNC Slant Thread Main Drive Gear/112T(H60G001XXW).

Requirements:
Motor pinion equipment 10T x 1
M4 set screw x 2(M4x4mm)

Right here is a great item that many others have actually bought at the same time.

Torque Tube

Use for T-REX 550/600/600 Nitro.
T-REX 550 Should with Tail Boom Brace(H60052A)、
Torque Tube(H60119-1)、
600 Carbon Tail Control Rod AssemblyH60221)

Requirements:
600 carbon fiber tail boom x 1(Φ20.3xΦ21.5x625mm)

Want an additional great item to match the above pointed out item?

DS615 Servo Gear Set

Request ALIGN DS615 Servo

Specifications:
DS615 equipment G1x1
DS615 equipment G2x1
DS615 equipment G3x1
DS615 equipment G4x1

This item compliments the main item below.

Skid Pipe

Apply to T-REX 550E.

Requirements:
Skid pipe x 2(Φ7.4xΦ9x294mm)
Skid pipe end cap x 4

The below item likewise sets actually well with the item being gone over.

Tail Boom

Request T-REX 550E

Specifications:
Tail boom x 2(Φ20.3xΦ21.5x549mm)
Tail control guide x 2
Rudder control rod x 1(Φ1.96x575mm)
Ball Link x 2

Get this item to boost the one you read about.

Tail Boom Brace

Request T-REX 550E

Requirements:
Tail boom brace set x 2
Tail boom brace x 2(Φ1.9xΦ3.9x412mm)
Self tapping screw x 2(M3x10mm)
Self tapping screw x 2(T3x10mm)
M3 washer x 4(Φ3xΦ8x1mm)

Right here is an additional item that compliments the item being gone over.

600 Carbon Fiber Tail Boom-Matte Black H60T003XX

Use for T-REX 550/600/600 Nitro.
T-REX 550 Should with Tail Boom Brace(H60052A)、
Torque Tube(H60119-1)、
600 Carbon Tail Control Rod AssemblyH60221)

Requirements:
600 carbon fiber tail boom x 1(Φ20.3xΦ21.5x625mm)

This item compliments the above gone over item.

New Landing Skid

This is an upgrade landing skid set for the Align 600 and 600N line of helicopters. More stiff than the standard landing equipment these have a reduced height for a lower center of mass more ideal for 3D flying.

Bundle consists of:

2 - Black landing skids approximately 39g each.