Vortex Hobbies 3S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a 3S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Below is an additional thing that compliments the thing being discussed.

2S JST-XH Lipo Balance Wire Extension Lead (8.6 IN)

This is a 2S JST-XH Lipo Balance Wire Extension Lead

Length:8.6 Inches

Below is an additional thing that compliments the thing being discussed.



Developed for use with 3 wire Brushless motor systems, this is
    the 3.5mm Gold Bullet Adapter Male from Great Planes.

FEATURES:
Gold plated

CONSISTS OF:
Three male bullet ports

REQUIRES:
Solder and soldering iron - HCAR0776 and STAR2000

SPECS:
Length: .47" (12mm)
Diameter: .14" (3.5mm) outside

REMARKS:
For the 3.5mm female adapter order GPMM3113

This thing compliments the above discussed thing.

11x7 Thin Electric Prop

This is a 11x7E Thin Composite propeller from Advanced Precision Composites.
For use on Electric powered aircraft just (not for radiance engines).

FUNCTIONS:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with five adjuster rings that adapt to different motor shafts.
Comes in a bag connected to a header card.

INCLUDES:
One composite propeller
Five composite adapter rings

REQUIRES:
ALL props require balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5006 (Metric)

SPECS:
Diameter: 11"
Pitch: 7
Hub inner diameter: 0.25"

Numerous others have gotten this thing along with the thing that you are presently reading about.

Venom Power Charger Lead w/EC3

This is the Venom EC3 Male to Battery charger Adapter.

FEATURES:
Connects a battery with an EC3 male plug to a charger with 4mm
    input jacks
14 AWG wire

CONSISTS OF:
11.75" (298mm) wire lead with 4mm banana plugs and EC3

Numerous others have gotten this thing along with the thing that you are presently reading about.



These are Female 2-Pin Flat Red Connectors with 3" wires.
This is also referred to as a JST connector.

FEATURES:
Developed for use with most Park Leaflet ElectriFly electronic devices
Red 2-pin flat adapter is a BEC-style
Wires are 24 gauge and pre-tinned at ends for simple soldering
One year quality guarantee

CONSISTS OF:
2 Female 2-Pin Red Connectors with 3" wires

REQUIRES:
Soldering to connect wires to application

SPECS:
Plug Size-
    Length: 19mm (total)
    Width: 7mm
    Height: 4mm

REMARKS:
For the male ports with wire, use GPMM3106.
This adapter can be used to replace BEC-type ports.

Frequently gotten with the thing that you are presently reading about.

10X6 Thin Electric Prop

This is a 10x6E Thin Composite propeller from Advanced Precision Composites
For use on Electric powered aircraft

FUNCTIONS:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with five adapter rings that suit propeller hub to allow
for different motor shaft diameters.

INCLUDES:
One composite propeller
Five composite adapter rings
Guideline sheet

REQUIRES:
All props require balancing. The Top Flite Power Point Propeller
Balancer (TOPQ5700) can be used for this purpose.
If prop reamer needed, use GPMQ5005 (SAE) or GPMQ5007 (Metric).

SPECS:
Diameter: 10" (250mm)
Pitch: 6
Hub inner diameter: 0.25" (6.4mm)
Adapter sizes: 3.3mm (1/8"), 4mm (5/32"), 4.9mm (3/16"),
6.0mm (1/4"), 8.0mm (5/16")

REMARKS:
This propeller must not be used on gas or radiance engines.