APC 11x7 Thin Electric Prop

This is a 11x7E Thin Composite propeller from Advanced Precision Composites.
For utilize on Electric powered airplane just (not for glow engines).

FUNCTIONS:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with 5 adjuster rings that adapt to various motor shafts.
Comes in a bag connected to a header card.

INCLUDES:
One composite propeller
5 composite adapter rings

REQUIRES:
ALL props require balancing, this is ESSENTIAL, utilize TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5006 (Metric)

SPECIFICATIONS:
Diameter: 11"
Pitch: 7
Hub inner size: 0.25"

The listed below product additionally sets really well with the product being gone over.

11x8 Thin Electric Prop

This is an 11x8E Thin Composite propeller from Advanced Precision Composites.
For utilize on Electric powered airplane just (not for glow engines).

FUNCTIONS:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with 5 adjuster rings that adapt to various motor shafts.
Comes in a bag connected to a header card.

INCLUDES:
One composite propeller
5 composite adapter rings

REQUIRES:
ALL props require balancing, this is ESSENTIAL, utilize TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Diameter: 11" (279mm)
Pitch: 8
Hub inner size: 0.25" (6.3mm)

Here is a great product that lots of others have actually purchased the exact same time.

10X6 Thin Electric Prop

This is a 10x6E Thin Composite propeller from Advanced Precision Composites
For use on Electric powered airplane

FUNCTIONS:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with 5 adapter rings that suit propeller center to permit
for various motor shaft diameters.

INCLUDES:
One composite propeller
5 composite adapter rings
Instruction sheet

REQUIRES:
All props require balancing. The Leading Flite Power Point Propeller
Balancer (TOPQ5700) can be used for this purpose.
If prop reamer needed, utilize GPMQ5005 (SAE) or GPMQ5007 (Metric).

SPECIFICATIONS:
Diameter: 10" (250mm)
Pitch: 6
Hub inner size: 0.25" (6.4mm)
Adapter sizes: 3.3mm (1/8"), 4mm (5/32"), 4.9mm (3/16"),
6.0mm (1/4"), 8.0mm (5/16")

REMARKS:
This propeller should not be used on gas or glow engines.

This product is frequently acquired with the above mentioned product.



Created for use with 3 wire Brushless motor systems, this is
    the 3.5mm Gold Bullet Port Male from Great Planes.

FEATURES:
Gold plated

INCLUDES:
3 male bullet connectors

REQUIRES:
Solder and soldering iron - HCAR0776 and STAR2000

SPECIFICATIONS:
Length: .47" (12mm)
Diameter: .14" (3.5mm) outside

REMARKS:
For the 3.5mm female connector order GPMM3113

Here is a great product that lots of others have actually purchased the exact same time.



These are Female 2-Pin Flat Red Connectors with 3" wires.
This is also referred to as a JST connector.

FEATURES:
Created for use with a lot of Park Flyer ElectriFly electronics
Red 2-pin flat connector is a BEC-style
Wires are 24 gauge and pre-tinned at ends for easy soldering
One year quality guarantee

INCLUDES:
2 Female 2-Pin Red Connectors with 3" wires

REQUIRES:
Soldering to link wires to application

SPECIFICATIONS:
Plug Size-
    Length: 19mm (total)
    Width: 7mm
    Height: 4mm

REMARKS:
For the male connectors with wire, use GPMM3106.
This connector can be used to replace BEC-type connectors.