Traxxas Stub Axles Rear (2)

These are the Rear Stub Axles
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal building, black and silver in color

CONSISTS OF:
2 rear stub axles and pins

SPECIFICATIONS:
Length: 1.65" (42mm)
Size: .51" (13mm) at largest point

Right here is an additional product that compliments the product being talked about.

Half Shafts Long Truck (2)

This is a set of telescoping drive shafts for the Blue Eagle LS II.

Includes: 2 white nylon telescoping shaft (each shaft is made from 2 pieces)
4 aluminum U-joints

pcd 01/23/94

Right here is an additional product that compliments the product being talked about.

Half Shafts Long Truck (6)

This is a set of the Traxxas telescoping drive shafts (equivalent of dogbones
or swing shafts). These are for usage on Traxxas trucks.

Features: White plastic parts

Includes:
(6) sets of drive shafts (each set includes an inside shaft wich
slides in the outside shaft).

Dimensions: 2.5" long when fully compressed.

Requires: Absolutely nothing else needed

This product is regularly gotten with the above discussed product.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Right here is a terrific product that numerous others have purchased the exact same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs install to the front A-arms and is what the
steering knuckles attach to.

FEATURES:
Nylon building, black in color
Stamped right and left to guarantee appropriate setup

CONSISTS OF:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and steering knuckles

The listed below product likewise sets truly well with the product being talked about.



This is the ST Racing Silver Aluminum Back Center Provider
for the Traxxas Slash 2WD, Stampede, Rustler and Bandit.

FEATURES:
Silver in color

CONSISTS OF:
One Silver Aluminum Back Center Provider

Right here is a terrific product that numerous others have purchased the exact same time.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock consisting of the shock oil.

FEATURES:
Nylon building

CONSISTS OF:
2 nylon shock cap (tops)
2 nylon shock cap (bottoms)

NEEDS:
Other shock parts

SPECIFICATIONS:
Size Tops Bottoms
16MM 13MM

COMMENTS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

Many others have gotten this product together with the product that you are presently reviewing.

Stub Axle Carriers (2) (R & S)

This is the Traxxas #3652 Stub Axle Provider that comes included with
the Rustler and Stampede trucks.

FEATURES:
Made of a black plastic/nylon material.
Also called the rear center or center carrier.
Has 2 possible install areas for the external hinge pin shaft.

INCLUDES.
2 Stub alxe carriers.

COMMENTS:
This holds the 2 5x8mm bushings (or bearings) on the stub
axle likewise called the wheel shaft.

AXY
3/25/95

Right here is a terrific product that numerous others have purchased the exact same time.

Diff Output Yokes Bk (2) W/3X5mm Cntrsnk Screws (2 ) &

These are the Differential Output Yokes
for the Traxxas Outlaw, Stampede and Rustler VXL.

FEATURES:
Black plastic building

CONSISTS OF:
2 differntial output yokes
2 3x5mm countersunk screws
2 screw pins

NEEDS:
Installation

SPECIFICATIONS:
Length: .70" (18mm)
Size: .51" (13mm)