Traxxas Servo Connector, Y-Adapter For Dual-Servo Steering Revo

This is the Servo Y Harness for the Double Steering Servos
for the REVO from Traxxas.

FEATURES:
Futaba J adapters (one male to enter into the RX and 2 female to
go to the servos)

INCLUDES:
One Y harness w/two 3" zip ties

NEEDS:
Absolutely nothing

SPECIFICATIONS:
Length: 3" (76mm) approx

This thing is often acquired with the above discussed thing.

Castle Bec 10Amp (25 Volt Max Input)

This is the CC BEC 10A Receiver Battery Eliminator by Castle Creations.

FEATURES:
Eliminates the requirement for a receiver and servo battery pack
Draws greater voltage from the motor batteries and drops it to a
    voltage level appropriate for the receiver and servos

INCLUDES:
One CC BEC receiver battery eliminator

NEEDS:
Setup in the aircraft

SPECIFICATIONS:
Length: 1.2" (30mm)
Width: .6" (15mm)
Height: .4" (10mm)
Weight: .4oz (11g)
Input voltage: 5V to 25.2V (2S to SIX LiPo)
Present output: 12 volts input = 7 amps* constant, 10 amp peak;
    24 volts input = 5 amps* constant, 7 amp peak
    *Ratings are figured out with a 5mph air flow on the BEC
Selectable Output: 4.8 - 9.0V by means of the Castle Link (sold individually)
    Default voltage is 5.1V

The below thing likewise pairs really well with the thing being talked about.



These are the EMS Unassembled Female Radio System Connectors.

FEATURES:
Suitable with Hitec, Airtronics Z and JR systems
Enables modelers to customized their own extensions, servo leads,
    battery leads and more
Gold plated for high conductivity and dependability
Fits wire sizes from 20 to 30 AWG
No soldering needed
Two year limited warranty

INCLUDES:
15 pins, 5 inner male adapters and 5 female shells,
    and guideline sheet

NEEDS:
Servo wire (HRCM3001)
Wire crimping tool

COMMENTS:
For the Male Connectors, order EMOM0017

This thing is often acquired with the above discussed thing.

King Off-Rd Pggybck Shocks w/Faux Reservoir 100

This is a set of King Off-Road 100mm Racing Shocks w/Faux Tank from RC4WD

FEATURES:
Machined billet aluminum construction
Double spring design
King logo on synthetic piggyback and retainer ring

INCLUDES:
Two 1/10 scale King Off-Road 110mm Racing Shocks w/Faux Tank

SPECIFICATIONS:
Hole to Hole (Compressed): 2.75" (70mm)
Hole to Hole (Uncompressed): 3.93" (100mm)
Total Length: 4.28" (108.9mm)
Travel Length: 1.18" (30mm)
Shock Body OD: 0.39" (10mm)
Spring Body OD: 0.57" (14.5mm)
Shaft Diameter: 0.17" (3.5mm)
Weight: 0.9oz (26g)

COMMENTS:
King Off-Road is a signed up trademark of the King Off-Road Shock
    company. The King Off-Road logo is property of King Off-Road
    Shocks.

This thing is often acquired with the above discussed thing.

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older design cases utilized on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

INCLUDES:
Fan with Wire Lead and Port
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Optimum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, remove before exposing ESC to moisture