Traxxas Servo Connector, Y-Adapter For Dual-Servo Steering Revo

This is the Servo Y Harness for the Dual Steering Servos
for the REVO from Traxxas.

FEATURES:
Futaba J adapters (one male to enter into the RX and two female to
go to the servos)

INCLUDES:
One Y harness w/two 3" zip ties

REQUIRES:
Absolutely nothing

SPECS:
Length: 3" (76mm) approx

This thing is frequently gotten with the above discussed thing.

Castle Bec 10Amp (25 Volt Max Input)

This is the CC BEC 10A Receiver Battery Eliminator by Castle Creations.

FEATURES:
Removes the need for a receiver and servo battery pack
Draws higher voltage from the motor batteries and drops it to a
    voltage level ideal for the receiver and servos

INCLUDES:
One CC BEC receiver battery eliminator

REQUIRES:
Installation in the airplane

SPECS:
Length: 1.2" (30mm)
Width: .6" (15mm)
Height: .4" (10mm)
Weight: .4oz (11g)
Input voltage: 5V to 25.2V (2S to SIX LiPo)
Existing output: 12 volts input = 7 amps* constant, 10 amp peak;
    24 volts input = 5 amps* constant, 7 amp peak
    *Ratings are identified with a 5mph air flow on the BEC
Selectable Output: 4.8 - 9.0V by means of the Castle Link (offered separately)
    Default voltage is 5.1V

The below thing likewise pairs actually well with the thing being talked about.



These are the EMS Unassembled Female Radio System Connectors.

FEATURES:
Suitable with Hitec, Airtronics Z and JR systems
Enables modelers to custom make their own extensions, servo leads,
    battery leads and more
Gold plated for high conductivity and reliability
Fits wire sizes from 20 to 30 AWG
No soldering required
Two year limited guarantee

INCLUDES:
15 pins, 5 inner male adapters and 5 female shells,
    and instruction sheet

REQUIRES:
Servo wire (HRCM3001)
Wire crimping tool

REMARKS:
For the Male Connectors, order EMOM0017

This thing is frequently gotten with the above discussed thing.

King Off-Rd Pggybck Shocks w/Faux Reservoir 100

This is a set of King Off-Road 100mm Racing Shocks w/Faux Tank from RC4WD

FEATURES:
Machined billet aluminum construction
Dual spring design
King logo on synthetic piggyback and retainer ring

INCLUDES:
Two 1/10 scale King Off-Road 110mm Racing Shocks w/Faux Tank

SPECS:
Hole to Hole (Compressed): 2.75" (70mm)
Hole to Hole (Uncompressed): 3.93" (100mm)
Total Length: 4.28" (108.9mm)
Travel Length: 1.18" (30mm)
Shock Body OD: 0.39" (10mm)
Spring Body OD: 0.57" (14.5mm)
Shaft Size: 0.17" (3.5mm)
Weight: 0.9oz (26g)

REMARKS:
King Off-Road is a registered trademark of the King Off-Road Shock
    business. The King Off-Road logo is home of King Off-Road
    Shocks.

This thing is frequently gotten with the above discussed thing.

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not deal with older design cases utilized on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws required

INCLUDES:
Fan with Wire Lead and Port
Fan Shroud

SPECS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Waterproof: NO, remove prior to exposing ESC to moisture