Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For use in all Traxxas TRX2.5 and TRX 3.3 equipped automobiles
Pull starter can be removed to install the EZ Start
60% more peak power than the TRX2.5, with nearly 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and radiance plug
One guideline manual (TRAZ5300)
One service assistance guide and parts lis.
One set of engine decals
One engine burglary DVD
One small bottle of air filter oil
One air filter

REQUIRES:
Vehicle fuel with 10%, 20% or 33% nitro material

SPECS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance between installing holes same side: 0.39" (10mm)
Distance between installing holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of installing flanges/top of cylinder head: 3.5" (88mm
Width of installing flanges: 44mm

COMMENTS:
Other versions of the TRX 3.3 engine include;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Right here is one more thing that praises the thing being discussed.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Requirement Connector.

FEATURES:
Suitable sport pack for automobiles, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Basic
    Adapter

REQUIRES:
NiMH compatible battery charger such as the Duratrax Onyx series

SPECS:
Capability: 3000mAh
Variety of Cells in Series: 6
Ranked Voltage: 7.2V
Minutes. Discharge Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Discharge Lead: 14AWG 2.7" (70mm) long wire w/Standard adapter
Load Dimensions: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This thing praises the main item right here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

BUNDLE
CONSISTS OF:
1-Diagonal Cone

FEATURES:
Black steel construction
Diagonal cone shape with split on one side

COMMENTS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Many others have purchased this thing in addition to the thing that you are presently reading about.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It permits you to mount the more recent 2.5 engine to an older T-Maxx.

FEATURES:
Tuned pipeline, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

CONSISTS OF:
One Plastic Tune Pipe w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carbohydrate Link Bellcrank (TRAC5167)
One Slide Carbohydrate Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post installing holes
Two Tie-Straps for installing Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm maker cap screw w/washer
One guideline sheet
One drilling template sheet

REQUIRES:
2.5 engine stock clutch system and stock engine mount

SPECS:
Tune Pipe Length: 101.6mm (4")
Header Pipe Outer Diameter: 13mm (.51")
Drill Bit size: 3.175mm (.125")

COMMENTS:
If EZ Start system is needed, use TRAP5271