Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For usage in all Traxxas TRX2.5 and TRX 3.3 equipped automobiles
Pull starter can be gotten rid of to set up the EZ Start
60% more peak power than the TRX2.5, with almost 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

INCLUDES:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and radiance plug
One direction manual (TRAZ5300)
One service assistance guide and parts lis.
One set of engine decals
One engine break-in DVD
One little bottle of air filter oil
One air filter

NEEDS:
Car fuel with 10%, 20% or 33% nitro content

SPECS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance between installing holes same side: 0.39" (10mm)
Distance between installing holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of installing flanges/top of cylinder head: 3.5" (88mm
Width of installing flanges: 44mm

COMMENTS:
Other versions of the TRX 3.3 engine consist of;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Below is an additional product that compliments the product being gone over.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Requirement Connector.

FEATURES:
Ideal sport pack for automobiles, trucks and boats

INCLUDES:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Basic
    Connector

NEEDS:
NiMH compatible battery charger such as the Duratrax Onyx series

SPECS:
Capability: 3000mAh
Variety of Cells in Series: 6
Rated Voltage: 7.2V
Min. Discharge Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Discharge Lead: 14AWG 2.7" (70mm) long wire w/Standard connector
Load Measurements: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 spot welds
Cell Size: Sub-C

This product compliments the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PLAN
INCLUDES:
1-Beveled Cone

FEATURES:
Black steel building and construction
Beveled cone shape with split on one side

COMMENTS:
Beveled cone sits in front of the flywheel
7/19/94sk

Numerous others have actually purchased this product in addition to the product that you are presently checking out.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It enables you to install the more recent 2.5 engine to an older T-Maxx.

FEATURES:
Tuned pipe, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

INCLUDES:
One Plastic Tune Pipe w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carb Link Bellcrank (TRAC5167)
One Slide Carb Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post installing holes
2 Tie-Straps for installing Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm device cap screw w/washer
One direction sheet
One drilling template sheet

NEEDS:
2.5 engine stock clutch system and stock engine install

SPECS:
Tune Pipe Length: 101.6mm (4")
Header Pipe Outer Size: 13mm (.51")
Drill Bit size: 3.175mm (.125")

COMMENTS:
If EZ Start system is needed, use TRAP5271