Traxxas 54T 0.8 P Spur Gear

This is the 54 Tooth Spur Equipment
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Equipment

REQUIRES:
Assembly onto vehicle

Lots of others have acquired this thing along with the thing that you are presently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Here is a wonderful thing that many others have purchased the exact same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum building and construction
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

REQUIRES:
Installation on to slipper shaft
Staying clutch pieces

You will certainly love this item if you have the item previously discussed.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Shielded with blue rubber seals

INCLUDES:
Two Ball Bearings

REQUIRES:
Assembly to vehicle

SPECS:
Inner Size: 10mm
External Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Main Clutch (one needed).

This thing compliments the above discussed thing.

13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is attached straight to the motor.

FEATURES:
Machined Steel
Developed for a 3mm shaft

INCLUDES:
One 13 tooth Pinion Equipment
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is just one of 2 which are utilized on the E-Maxx double motor
    set-up.

This thing compliments the above discussed thing.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

This is a superb addition to the thing presently being discussed.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction
Black in color

INCLUDES:
One Input Shaft
One Bearing Adapter
One Pin

REQUIRES:
Installation on the vehicle

SPECS:
Length: 58mm (2.3")

Here is an additional thing that compliments the thing being discussed.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FUNCTIONS:
Fully assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping sections from dirt
Connects to the differential with one screw pin
Works on the front or rear, right or left of vehicle

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Instruction sheet

REQUIRES:
Setting up on chassis