HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Back Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic building

CONSISTS OF:
Left and Right Front Knuckles and Back Uprights with 4 Hex Inserts

You will like this item if you have the item just above pointed out.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Center Providers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic building

CONSISTS OF:
Left and Right Front Center Providers

REQUIRES:
Four 5x10mm Ball Bearings, DTXC1535

You will like this item if you have the item just above pointed out.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System permits connection between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect preferred plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Vehicle balancer (TCPP9150)

SPECIFICATIONS:
Setup: 2S
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

REMARKS:
READ the ENTIRE direction sheet included with battery prior to use
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER permit to Release listed below 2.5V per cell
NEVER disassemble or modify pack circuitry in any way or puncture cells
NEVER put on flammable materials or leave ignored throughout
charging
ALWAYS charge in a fireproof area
ALWAYS set battery charger's output volts to match battery volts
ALWAYS keep out of reach of children

This item praises the main item below.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to secure versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

This item is often bought with the above mentioned item.

Flanged Lock Nut, M4, (4Pcs), Bullet St/Mt, Rs4, Venture, Sport

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be utilized for wheels, slipper clutch springs, & other applications
    which require easy elimination and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECIFICATIONS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")