JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

Hitec HS-55 Servo Economy Sub Micro Univ (Hitec 31055S | HRC31055S)
Due to the impact of the COVID-19/Corona virus, there my be delays in the shipping estimates shown on our site.

We appreciate your understanding and support during these uncertain times.

Model: Hitec 31055S
Dist. #: HRCM0982   SKU: HRC31055S

Be the first to review this product. (Write Review)

Shipping: In Stock For Shipping
Store Pickup:

South Jordan, UT
Ship To Store - Pick up in 1 to 2 days..

List Price:  $17.15
Price:  $11.49
You Save:  $5.66 (33%)

This item will earn you 11 reward point(s).
11 points = $0.22 off your next order. Learn More

Updated on Jul 8, 2020 03:22:22 PM

HS-55 Servo Economy Sub Micro Univ...
    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

Extremely slim case and lightweight for installing in small airplanes,
    electrics or gliders, where really high speed and great torque are
One of the slimmest micro servos available.
High-strength resin gear train offers reputable operation.

One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One really small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
2 M1.7x7 servo installing screws

at 4.8V
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This product is regularly purchased with the above discussed product.

This is the Futaba S3003 Requirement Servo.
This basic servo is used in vehicles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make sure they are capable
of providing adequate amps.

One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo install screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year guarantee

Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

Regularly purchased with the product that you are currently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a great deal of torque even at low speeds.

Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building and construction minimizes turning mass for
    higher output and longer life.
Reinforcing carbon fibers assist maintain true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type

One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring instruction sheet

ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

Length: 8"
Pitch: 3.8

Slo-Flyer props are Not created for Radiance engines

The below product additionally sets actually well with the product being talked about.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

Light-weight molded nylon building and construction minimizes turning mass for
    higher output and longer life
Created for electrical powered Park Flyer type airplane with rear
    dealing with motors that "push" the aircraft forward

8x3.8 Slo-Flyer Pusher Propeller with two locating rings and
    instruction sheet

Length: 8" Pitch: 3.8"
Hub Thickness: 0.30" Hub diameter: 0.50"
Hole Diameter: 1/4"

Just for use with electrical motors. Not for use with glow or gas
All props require balancing, this is EXTREMELY IMPORTANT, use TOPQ5700.
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

Frequently Bought Together

Hitec HS-55 Servo Economy Sub Micro Univ
Spektrum DXe Transmitter Only
Volantex  Trainstar Exchange Rubber Bands (6Pcs)
This Item: Hitec HS-55 Servo Economy Sub Micro Univ
Spektrum DXe Transmitter Only
Volantex Trainstar Exchange Rubber Bands (6Pcs)

Total Price: $83.47

Add All Three To Cart

Customers who bought this product also purchased

Visual Parts Finder