Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Equipment Micro Servo from Hitec.

FEATURES:
For little planes, gliders, electrical helicopters and 1/18 scale automobiles

CONSISTS OF:
HS-82MG Metal Equipment Micro Servo with universal adapter, 0.67" (17mm)
    size horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and mounting hardware

NEEDS:
Setting up in design and linking to receiver

SPECIFICATIONS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

REMARKS:
The following replacement parts are offered;
Equipment Set, HRCM6386
Horn Set, HRCM6326

Want an additional excellent product to compliment the above pointed out product?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high performance airplanes. Providing
45A of constant present with an integrated Battery Circuit
which can deal with 2A, this ESC is simple to use
and extremely affordable.

FEATURES:
Compatible with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz changing frequency, for excellent run time and cool operation
Pre-installed Universal radio adapter* (see Remarks listed below)
Pre-installed WS Deans Ultra male adapter for battery (see
Remarks listed below)
Pre-installed gold plated 4mm female bullet adapters for motor
High powered changing BEC (Battery Eliminator Circuit) which
    manages 3 or 4 basic servos
Full proportional forward and smooth throttle response with ON/OFF
    brake
Safe Start System** (see information in Remarks listed below)
Thermal Defense stops motor when maximum temperature 230°F
    is reached
180 Day Service warranty (U.S.A & Canada Only)

CONSISTS OF:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver adapter, battery adapter, and motor
    adapters.

REQUIRES:
Mating motor connectors, usage: GPMM3114
Mating battery adapter, usage: WSDM3000

SPECIFICATIONS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Existing: 45A constant maximum
50A rise maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Operating frequency: 16kHz fixed
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

REMARKS:
To use with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle adhere to complete throttle position,
then to "OFF" position, then gradually advance throttle and motor will
start to run.

The "Silver Series" line of brushless electronic speed controls
    consist of numerous built-in safety features. One such function COULD
    POSSIBLY CAUSE THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an extremely low position and/or if
    rotation of the brushless motor is hindered or obstructed in some
    way. This is NORMAL, as the ESC is spotting that a problem
    possibly exists with the motor and/or speed control. Rotation of
    the motor is stopped to protect the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually currently been armed and the motor has been
rotating normally, yet after moving the throttle adhere to near minimum the
motor all of a sudden stops to turn normally even if the throttle stick is advanced
above minimum throttle, DO NOT PLACE YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS CAUTION COULD LEAD TO INJURY!! From this point, moving
the throttle stick up - even to complete throttle may not cause the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To gain back
control of the motor, move the throttle adhere to outright minimum throttle
position and then advance the throttle stick upwards when again.
Alternatively, you can disconnect the battery from the ESC, then re-connect the
power source and re-arm the system.
NEVER
come up to the propeller if the speed control is connected to input power!
ALWAYS
ensure the throttle stick is at minimum position before attempting to
disconnect the battery from the speed control! ElectriFly is not responsible
for incidental damage or accident as an outcome of abuse of this item.