Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Gear Micro Servo from Hitec.

FEATURES:
For small airplanes, gliders, electric helicopters and 1/18 scale vehicles

CONSISTS OF:
HS-82MG Metal Gear Micro Servo with universal connector, 0.67" (17mm)
    size horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and installing hardware

REQUIRES:
Setting up in model and connecting to receiver

SPECS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

REMARKS:
The following replacement parts are available;
Gear Set, HRCM6386
Horn Set, HRCM6326

Want an additional great item to match the above mentioned item?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high efficiency airplanes. Delivering
45A of continuous existing with an integrated Battery Circuit
which can handle 2A, this ESC is basic to use
and very affordable.

FEATURES:
Compatible with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz switching frequency, for excellent run time and cool operation
Pre-installed Universal radio connector* (see Remarks below)
Pre-installed WS Deans Ultra male connector for battery (see
Remarks below)
Pre-installed gold plated 4mm female bullet connectors for motor
High powered switching BEC (Battery Remover Circuit) which
    handles 3 or 4 conventional servos
Complete proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see details in Remarks below)
Thermal Security stops motor when maximum temperature 230°F
    is reached
180 Day Service warranty (USA & Canada Only)

CONSISTS OF:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver connector, battery connector, and motor
    connectors.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery connector, use: WSDM3000

SPECS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Existing: 45A continuous maximum
50A surge maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Running frequency: 16kHz fixed
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

REMARKS:
To use with "Old Airtronics" Rx, needs adapter: AIRM4400

**Safe Start System: Move throttle stay with complete throttle position,
then to "OFF" position, then gradually advance throttle and motor will
start to run.

The "Silver Series" line of brushless electronic speed controls
    consist of many built-in security features. One such function COULD
    PERHAPS TRIGGER THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at an incredibly low position and/or if
    rotation of the brushless motor is hampered or obstructed in some
    method. This is NORMAL, as the ESC is finding that a problem
    potentially exists with the motor and/or speed control. Rotation of
    the motor is stopped to protect the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually already been equipped and the motor has been
rotating typically, yet after moving the throttle stay with near minimum the
motor unexpectedly ceases to rotate typically even if the throttle stick is advanced
above minimum throttle, DO NOT RESTAURANT YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD RESULT IN INJURY!! From this point, moving
the throttle hold up - even to complete throttle might not cause the motor to
rotate BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To gain back
control of the motor, move the throttle stay with absolute minimum throttle
position and after that advance the throttle stick upwards when again.
Alternatively, you can detach the battery from the ESC, then re-connect the
source of power and re-arm the system.
NEVER
come up to the propeller if the speed control is linked to input power!
ALWAYS
make certain the throttle stick is at minimum position prior to trying to
detach the battery from the speed control! ElectriFly is not responsible
for incidental damage or personal injury as a result of misuse of this item.