Align 2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Instruction::
Max Continuous Discharge: 30C. Normal operating temperature is approx. 40-65?C(within 80% of ranked discharge). Max. temperature: 80?C.
Recommend to discharge the battery within 80% of ranked discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and efficiency will lower due to high existing, high temperature and over-discharge)

NOTE::
When using high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature. Discharging capacity can't surpass 80% of limit capacity after complete charging to ensure a great cycle performance.Recommend to complete charge a brand brand-new battery prior to using and only discharge the battery 50% for very first 5 times making a great efficiency of the battery. Please make it a routine to constantly count time for flight, or please set a low voltage protection on ESC (Cell voltage after stopping using can not lower than 3.4V). Do not utilize the battery at inadequate of voltage.

Do not expose batteries to sunlight or shop/ charge batteries at the temperature approximately 35℃ in a airtight car. The environment high temperature could trigger the damage or the threat of burst. If the battery ends up being hot while high existing discharging or flying, please do not charge the battery immediately. Wait to cool down(about 20 mins), then check to recharge. If against follow the initial factory using guidelines, possibly trigger the battery to pump up or any unsafe accident happens.
Do not leave the battery charger is operating ignored as it might trigger a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Dimension:47x21.5x12mm
Weight:15g

This is a fantastic enhancement to the thing presently being gone over.

T-Rex 150 DFC Combo BTF Twin BL Motor, 2S 7.4V 250Mah

Align's tiniest and most small 3D helicopter T-Rex 150 DFC, brings the very same remarkable pedigree and design principle that stemmed from the effective T-Rex line of helicopters. Including strong power, remarkable flight control stability, and equipped with high-end elements, far exceeding other helicopters currently on the market.

Twin brushless motor design, coupled with 2s 7.4v 250mah battery, producing power that will surpass all your expectations. Metal DFC main rotor head assembly including high-end aesthetic and remarkable flight performance; in addition, an incorporated control system with specially enhanced 3-axis gyro, receiver, electronic speed controller, and 4g servos. All these allow the T-Rex 150 DFC to posses the very same stability, remarkable dexterity, and tail holding effectiveness as the bigger helicopters.

T-Rex 150 functions built in Futaba S-FHSS 2.4Ghz system, and support the use of Spektrum DSM2/DSMX / JR DSM2/DSMJ/DMSS satellite receivers. To get the T-Rex 150 airborne, all thats required is inputting of criteria noted in handbook into your transmitter, and binding of your transmitter.

Miniature size, control precision that appears like the bigger helicopters, allows you to enjoy flying inside a confined space. Novices can even enjoy this with ease by simply turning down the speed dial. The ingenious advancement T-Rex 150 will bring you a brand-new dimension of flying enjoyment.

Specification:
Length: 255mm
Height: 80mm
Main Blade Length: 120mm
Main Rotor Diameter: 271mm
Tail Rotor Diameter: 41mm
Motor Pinion Gear: 10T
Main Drive Gear: 78T
Drive Gear Ratio: 1:7.8
Weight (w/o Battery): 53g

Devices:
T-REX 150 DFC Set x 1
Main Blades x 2set
Tail Blades x 1
150M Main Motor x 1
150M Tail Motor x 1
S150 micro Servo x 2
DS155 micro Servo x 1
Blnd Plug x 1
Remote Extension x 1
7.5V Li-Po 250mAh Li-Polymer Battery x 1

Radio transmitter and electronic equipment needed for assembly:
1.ALIGN T6 or Futaba S-FHSS 2.4G Transmitter or JR DSM2/DSMJ/DMSS、Spektrum DSM2/DSMX 2.4GHz Transmitter