Align 150 Tail Boom

Usage for T-REX 150.

Requirements:
150 tail boom x 2(3.5x3.5x140mm)
150 Tail motor install x 2
Socket button head self screw x 2(T1.5x3mm)
Socket button head screw x 2(#0-80x3mm)

Often bought with the product that you are currently reviewing.

150 Main Shaft

Usage for T-REX 150.

Requirements:
Main Shaft x 2(Φ1.6xΦ3x45.8mm)
Socket button head screw x 2(M2x4mm)

Want an additional wonderful product to enhance the above stated product?

150 Landing Skid

Usage for T-REX 150.

Requirements:
Landing Skid x 2
Landing Skid nut x 8(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 4(T1.5x3mm)

Want an additional wonderful product to enhance the above stated product?

20 Tail Blade

Usage for T-REX 150.

Requirements:
Tail Blade x 4
Length:41.35 mm
Weight:Approx 0.21g/single

This is a amazing enhancement to the product currently being discussed.

150 Vertical Stabilizer

Usage for T-REX 150.

Requirements:
Vertical Stabilizer x 2

Lots of others have actually bought this product together with the product that you are currently reviewing.

2S1P 7.4V 250mAh/30C

Usage for T-REX 150.

Guideline::
Max Constant Discharge: 30C. Normal operating temperature is approx. 40-65?C(within 80% of ranked discharge). Max. temperature: 80?C.
Recommend to discharge the battery within 80% of ranked discharge, keep 95% capability when over 100 cycles, keep 90% capability when over 150 cycles.(The cycle life and efficiency will minimize due to high existing, high temperature and over-discharge)

NOTE::
When using high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature. Discharging capability can't surpass 80% of limit capability after full charging to make sure a good cycle performance.Recommend to full charge a brand brand-new battery prior to using and just discharge the battery 50% for very first 5 times to make a good efficiency of the battery. Please make it a routine to constantly count time for flight, or please set a low voltage protection on ESC (Cell voltage after stopping using can not decrease than 3.4V). Do not use the battery at insufficient of voltage.

Do not expose batteries to sunlight or store/ charge batteries at the temperature approximately 35℃ in a airtight automobile. The environment high temperature could cause the issue or the threat of burst. If the battery becomes hot while high existing discharging or flying, please do not charge the battery instantly. Wait to cool off(about 20 mins), then check to recharge. If versus follow the original factory using rules, perhaps cause the battery to inflate or any unsafe mishap takes place.
Do not leave the charger is operating ignored as it may cause a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Measurement:47x21.5x12mm
Weight:15g

Lots of others have actually bought this product together with the product that you are currently reviewing.

120 Main Blades-Black

Usage for T-REX 150.

Requirements:
Forming: Balanced wing
Length:120 mm
Weight:Approx 5.8g/set

Accessories:
Main Blades x 2 set
Main blade Decal x 1 set

Here is a wonderful product that many others have actually bought at the same time.

150 Feathering Shaft

Usage for T-REX 150.

Requirements:
150 Feathering shaft x 3(Φ2x16.5mm)
Socket Button Head Screw x 6(#0-80x3mm)
100 Spacer x 6(Φ1.6x3.2x0.2mm)