Align 150 Spare Parts Pack

Use for T-REX 150.

Specs:
Socket button head screw x 5(#0-80x6.2mm)
Washer x 4(Φ2xΦ3.6x0.2mm)
150 Head Damper x 2(Φ2xΦ4x1.3mm)
Socket Button Head Screw x 5(#0-80x3mm)
100 Spacer x 4(Φ1.6xΦ3.2x0.2mm)
Socket button head screw x 4(#0-80x8mm)
Φ2.1 Linkage ball A x 5(Φ2.1x4.28mm)
Socket button head screw x 2(M2x4mm)
Cross screw x 2(T1.5x4mm)
150 Ball Link A x 2(Φ2.1x13.3x2mm)
150 Ball Link B x 4(Φ2.1x10.5x2mm)
150 Landing Skid Spacer x 4(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 5(T1.5x3mm)
Socket button head self tapping screw x 5(T1.5x4mm)
Motor Pinion Gear 10T x 1
100 Canopy nut x 4
Strap x 5(1.6x71mm)

Want an additional excellent thing to compliment the above pointed out thing?

150 Main Shaft

Use for T-REX 150.

Specs:
Main Shaft x 2(Φ1.6xΦ3x45.8mm)
Socket button head screw x 2(M2x4mm)

This thing is regularly gotten with the above pointed out thing.

DS150 Digital Servo

Ideal for T-Rex 150

Guidelines:
4g digital micro servos are special design for T-REX 150 DFC, includes to increase micro helicopter control speed and accuracy, let the micro/indoor helicopter has same flight efficiency as large/outdoor helicopter.

Specs:
Stall torque:0.8kg．cm(5V)
Motion speed:0.06 sec/60?(5V)
Score voltage:DC 4.8-6V
Dimension:19.8x8.4x23.3mm
Weight:4.3g
1520μs basic band

Accessories:
DS150/155 Servo rudder piece x 1
Socket button head self tapping scre x 1(T1.5x3mm)

Want an additional excellent thing to compliment the above pointed out thing?

100 Main Drive Gear

This is a replacement Align Main Drive Gear, and is meant for use with the Align T-Rex 100 helicopter.



This is a superb enhancement to the thing presently being gone over.

150 Landing Skid

Use for T-REX 150.

Specs:
Landing Skid x 2
Landing Skid nut x 8(Φ1.5xΦ3x2mm)
Socket button head self tapping screw x 4(T1.5x3mm)

Want an additional excellent thing to compliment the above pointed out thing?

2S1P 7.4V 250mAh/30C

Use for T-REX 150.

Instruction::
Max Continuous Discharge: 30C. Typical operating temperature level is approx. 40-65?C(within 80% of ranked discharge). Max. temperature level: 80?C.
Recommend to release the battery within 80% of ranked discharge, keep 95% capacity when over 100 cycles, keep 90% capacity when over 150 cycles.(The cycle life and effectiveness will reduce due to high present, high temperature level and over-discharge)

KEEP IN MIND::
When using high energy Li-poly Battery, please do not over-discharge, over-charge batteries, or result over-high temperature level. Discharging capacity cannot exceed 80% of the max capacity after complete crediting make sure an excellent cycle performance.Recommend to complete charge a brand name brand-new battery before using and only release the battery 50% for first 5 times to make an excellent effectiveness of the battery. Please make it a routine to always count time for flight, or please set a low voltage defense on ESC (Cell voltage after stopping using can not decrease than 3.4V). Do not utilize the battery at inadequate of voltage.

Do not expose batteries to sunlight or store/ charge batteries at the temperature level approximately 35℃ in a airtight car. The environment high temperature level could cause the damage or the risk of burst. If the battery ends up being hot while high present discharging or flying, please do not charge the battery right away. Wait to cool off(about 20 mins), then inspect to recharge. If versus follow the initial factory using rules, possibly cause the battery to pump up or any unsafe mishap occurs.
Do not leave the battery charger is operating unattended as it might cause a fire.

Specifications:
Output:7.4V250mAh (2S1P)
Dimension:47x21.5x12mm
Weight:15g