Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a SIX JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The listed below thing also pairs really well with the thing being gone over.

4S JST-XH Lipo Balance Wire Extension Lead

This is a 4S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Many others have acquired this thing together with the thing that you are currently checking out.

EC5 Device Connector (2)


Features



Capable of more than 120A constant present with 10-awg wireErgonomically pleasing and simple to gripProtected to avoid shorting and reverse polaritySuperior technology fit to today's sophisticated applicationsDesigned with benefit and reliability in mind




Overview


E-flite's high-quality EC5 ports ought to be a staple for each workbench. EC5 (E-flite Port 5mm) ports, leads with ports, and devices are best for electrical power applications and deal with any battery, charger, ESC, Power Meter, etc. They are perfect for high power applications.

Many others have acquired this thing together with the thing that you are currently checking out.

EC5 Extension Lead with 6" Wire, 10Awg




Frequently acquired with the thing that you are currently checking out.

Servo line Color Black & Green

Planning to tidy up the appearance of your helicopter, plane of RC vehicle & protect your servo lines from chaffing? Servo Line Covering is an easy method to protect your servo wires, including a tidy, visual seek to your RC device, and can be set up in a matter of minutes. Select from our amazing line of diverse colors to add a whole makeover to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal inside. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a suitable sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat gun to diminish it down around the covering, thus giving you a flush, tight fit over the formerly frayed servo covering. Do the very same with the end of your servo wire, being careful to leave the terminal bare so it can easily plug into your receiver. Also, make sure to keep in mind of the servo wire polarity if you cover the full wire – this will ensure that you will know exactly what instructions to plug your servo terminal into your receiver.

Here is a wonderful thing that several others have purchased the same time.

Servo line Color Blue/Black (1m)

Planning to tidy up the appearance of your helicopter, plane of RC vehicle & protect your servo lines from chaffing? Servo Line Covering is an easy method to protect your servo wires, including a tidy, visual seek to your RC device, and can be set up in a matter of minutes. Select from our amazing line of diverse colors to add a whole makeover to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal inside. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a suitable sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat gun to diminish it down around the covering, thus giving you a flush, tight fit over the formerly frayed servo covering. Do the very same with the end of your servo wire, being careful to leave the terminal bare so it can easily plug into your receiver. Also, make sure to keep in mind of the servo wire polarity if you cover the full wire – this will ensure that you will know exactly what instructions to plug your servo terminal into your receiver.