Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a SIX JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The listed below thing likewise sets really well with the thing being talked about.

4S JST-XH Lipo Balance Wire Extension Lead

This is a FOUR JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Many others have acquired this thing along with the thing that you are presently reviewing.

EC5 Device Connector (2)


Functions



Capable of more than 120A constant present with 10-awg wireErgonomically pleasing and easy to gripProtected to prevent shorting and reverse polaritySuperior innovation suited to today's advanced applicationsDesigned with convenience and reliability in mind




Overview


E-flite's top quality EC5 ports should be a staple for every single workbench. EC5 (E-flite Adapter 5mm) ports, leads with ports, and devices are best for electric power applications and work with any battery, battery charger, ESC, Power Meter, etc. They are ideal for high power applications.

Many others have acquired this thing along with the thing that you are presently reviewing.

EC5 Extension Lead with 6" Wire, 10Awg




Frequently acquired with the thing that you are presently reviewing.

Servo line Color Black & Green

Wanting to tidy up the look of your helicopter, airplane of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, adding a tidy, aesthetic seek to your RC device, and can be installed in a matter of minutes. Select from our exciting line of different colors to add a whole make over to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat weapon to diminish it down around the covering, thus providing you a flush, tight fit over the formerly frayed servo covering. Do the exact same with completion of your servo wire, bewaring to leave the terminal bare so it can quickly plug into your receiver. Also, be sure to bear in mind of the servo wire polarity if you cover the complete wire – this will make sure that you will know exactly what direction to plug your servo terminal into your receiver.

Right here is a great thing that several others have purchased the very same time.

Servo line Color Blue/Black (1m)

Wanting to tidy up the look of your helicopter, airplane of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, adding a tidy, aesthetic seek to your RC device, and can be installed in a matter of minutes. Select from our exciting line of different colors to add a whole make over to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the included heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat weapon to diminish it down around the covering, thus providing you a flush, tight fit over the formerly frayed servo covering. Do the exact same with completion of your servo wire, bewaring to leave the terminal bare so it can quickly plug into your receiver. Also, be sure to bear in mind of the servo wire polarity if you cover the complete wire – this will make sure that you will know exactly what direction to plug your servo terminal into your receiver.