Vortex Hobbies 6S JST-XH Lipo Balance Wire Extension Lead (12 IN)

This is a SIX JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

The below thing also pairs truly well with the thing being discussed.

4S JST-XH Lipo Balance Wire Extension Lead

This is a 4S JST-XH Lipo Balance Wire Extension Lead

Length: 12 Inches

Lots of others have purchased this thing along with the thing that you are currently reading about.

EC5 Device Connector (2)


Features



Efficient in more than 120A constant present with 10-awg wireErgonomically pleasing and simple to gripProtected to prevent shorting and reverse polaritySuperior technology suited to today's advanced applicationsDesigned with benefit and dependability in mind




Overview


E-flite's top quality EC5 connectors ought to be a staple for every workbench. EC5 (E-flite Adapter 5mm) connectors, leads with connectors, and accessories are best for electric power applications and work with any battery, charger, ESC, Power Meter, and so on. They are perfect for high power applications.

Lots of others have purchased this thing along with the thing that you are currently reading about.

EC5 Extension Lead with 6" Wire, 10Awg




Frequently purchased with the thing that you are currently reading about.

Servo line Color Black & Green

Planning to clean up the look of your helicopter, plane of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, including a clean, visual want to your RC maker, and can be installed in a matter of minutes. Choose from our amazing line of varied colors to add an entire makeover to your RC machine!

Included In Bundle:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal inside. It works best to "inch worm" your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat weapon to shrink it down around the covering, thus providing you a flush, tight fit over the formerly frayed servo covering. Do the very same with the end of your servo wire, taking care to leave the terminal bare so it can easily connected into your receiver. Likewise, make certain to remember of the servo wire polarity if you cover the complete wire – this will ensure that you will know exactly what instructions to plug your servo terminal into your receiver.

Below is a fantastic thing that numerous others have bought at the exact same time.

Servo line Color Blue/Black (1m)

Planning to clean up the look of your helicopter, plane of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, including a clean, visual want to your RC maker, and can be installed in a matter of minutes. Choose from our amazing line of varied colors to add an entire makeover to your RC machine!

Included In Bundle:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal inside. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat weapon to shrink it down around the covering, thus providing you a flush, tight fit over the formerly frayed servo covering. Do the very same with the end of your servo wire, taking care to leave the terminal bare so it can easily connected into your receiver. Likewise, make certain to remember of the servo wire polarity if you cover the complete wire – this will ensure that you will know exactly what instructions to plug your servo terminal into your receiver.