Traxxas Suspension Pins 44Mm Slash Rustler / Stampede / Bandit

This is a set of chrome suspension pins used to hold the front suspension arms
on the TRAXXAS SRT, NITRO STAMPEDE, and NITRO RUSTLER.

Includes: 2 chrome suspension pins and 3 "E" type retaining clips.

Requires:absolutely nothing parts are a direct replacement.

Specs:3mm x 44mm pins are notched for the 3MM "E" type retaining clips at each
end. WLG 9-29-97

This is a superb addition to the item presently being talked about.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FUNCTIONS:
Fiberglass Building and construction

CONSISTS OF:
One Tie Bar

REQUIRES:
Suspension Pins (TRAC4940)

SPECS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Thickness: 2.0 mm (0.082")

COMMENTS:
None

Here is a fantastic item that several others have purchased the exact same time.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FUNCTIONS:
Resilient steel building

CONSISTS OF:
Two 48mm pins
Two 34mm pins
Two 30mm pins
Two 28mm pins
Two 25mm pins

REQUIRES:
Installation on the Rustler, Stampede or Outlaw

COMMENTS:
For a complete suspension pin set order TRAC4940

This item praises the above talked about item.

Front Bulkhead (Black) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead used in lots of Traxxas vehicles.
The front suspension arm hinge pins go through this piece.

FEATURES:
Black nylon building

CONSISTS OF:
One front bulkhead

REQUIRES:
Nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

COMMENTS:
This part is used on the following automobiles:
    Rustler, Outlaw, Stampede, Nitro Rustler, SRT, Nitro Stampede.

This item praises the above talked about item.

Front Bulkhead (Gray) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead used in lots of Traxxas vehicles.
The front suspension arm hinge pins pass through this piece.

FEATURES:
Gray nylon building

CONSISTS OF:
One front bulkhead

REQUIRES:
Nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

COMMENTS:
This part is used on the following automobiles:
    Rustler, Outlaw, Stampede, Nitro Rustler, SRT, Nitro Stampede,
    Rustler XL and Stampede XL.

Here is a fantastic item that several others have purchased the exact same time.

Wide Front Bumper, For Traxxas Rustler/Stampede/ Nitro Sport/Ban

This is a Wide Front Bumper for the Traxxas Rustler and Stampede.
The Bumper goes on the Front of the Car and Secures the Chassis.

FEATURES:
Resilient Plastic Building and construction
Black in Color

CONSISTS OF:
One Bumper
One Group RPM Decal

REQUIRES:
Installation onto the Traxxas Rustler or Stampede.

SPECS:
Length: 2-3/4"
Width: 6-1/8"

COMMENTS:
The Factory Number is #81162

Here is a fantastic item that several others have purchased the exact same time.

Rod Ends Long & Short

This set of rod ends, balls, and screws is used on all however four of Traxxas'
kits. It WILL NOT WORK ON: the Sledgehammer, initial Hawk, Cat, or Bullet.

Includes: 4 brief rod ends (17mm)
16 long rod ends (19mm)
2 ball screws
18 hollow ball connectors

pcd 01/23/94