Traxxas Stub Axles Rear (2)

These are the Rear Stub Axles
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal building, black and silver in color

INCLUDES:
2 rear stub axles and pins

SPECIFICATIONS:
Length: 1.65" (42mm)
Size: .51" (13mm) at largest point

Here is another product that compliments the product being talked about.

Half Shafts Long Truck (2)

This is a set of telescoping drive shafts for heaven Eagle LS II.

Includes: 2 white nylon telescoping shaft (each shaft is made of two pieces)
4 aluminum U-joints

pcd 01/23/94

Here is another product that compliments the product being talked about.

Half Shafts Long Truck (6)

This is a set of the Traxxas telescoping drive shafts (equivalent of dogbones
or swing shafts). These are for use on Traxxas trucks.

Features: White plastic parts

Consists of:
(6) sets of drive shafts (each set consists of an inside shaft wich
slides in the outdoors shaft).

Measurements: 2.5" long when fully compressed.

Requires: Absolutely nothing else needed

This product is regularly gotten with the above mentioned product.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Here is a fantastic product that lots of others have purchased the very same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is exactly what the
guiding knuckles connect to.

FEATURES:
Nylon building, black in color
Stamped right and left to insure right setup

INCLUDES:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and guiding knuckles

The below product likewise pairs actually well with the product being talked about.



This is the ST Racing Silver Aluminum Back Center Provider
for the Traxxas Slash 2WD, Stampede, Rustler and Bandit.

FEATURES:
Silver in color

INCLUDES:
One Silver Aluminum Back Center Provider

Here is a fantastic product that lots of others have purchased the very same time.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock consisting of the shock oil.

FEATURES:
Nylon building

INCLUDES:
2 nylon shock cap (tops)
2 nylon shock cap (bottoms)

NEEDS:
Other shock elements

SPECIFICATIONS:
Size Tops Bottoms
16MM 13MM

COMMENTS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

Numerous others have gotten this product along with the product that you are presently checking out.

Stub Axle Carriers (2) (R & S)

This is the Traxxas #3652 Stub Axle Provider that comes included with
the Rustler and Stampede trucks.

FEATURES:
Made of a black plastic/nylon material.
Also called the rear hub or hub carrier.
Has 2 possible install areas for the outer hinge pin shaft.

INCLUDES.
2 Stub alxe carriers.

COMMENTS:
This holds the two 5x8mm bushings (or bearings) on the stub
axle likewise called the wheel shaft.

AXY
3/25/95

Here is a fantastic product that lots of others have purchased the very same time.

Diff Output Yokes Bk (2) W/3X5mm Cntrsnk Screws (2 ) &

These are the Differential Output Yokes
for the Traxxas Bandit, Stampede and Rustler VXL.

FEATURES:
Black plastic building

INCLUDES:
2 differntial output yokes
2 3x5mm countersunk screws
2 screw pins

NEEDS:
Installation

SPECIFICATIONS:
Length: .70" (18mm)
Size: .51" (13mm)