Traxxas Stub Axles Rear (2)

These are the Rear Stub Axles
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal building, black and silver in color

CONSISTS OF:
2 rear stub axles and pins

SPECS:
Length: 1.65" (42mm)
Diameter: .51" (13mm) at biggest point

Here is an additional thing that praises the thing being discussed.

Half Shafts Long Truck (2)

This is a set of telescoping drive shafts for the Blue Eagle LS II.

Includes: 2 white nylon telescoping shaft (each shaft is made of 2 pieces)
4 aluminum U-joints

pcd 01/23/94

Here is an additional thing that praises the thing being discussed.

Half Shafts Long Truck (6)

This is a set of the Traxxas telescoping drive shafts (equivalent of dogbones
or swing shafts). These are for use on Traxxas trucks.

Features: White plastic parts

Includes:
(6) sets of drive shafts (each set consists of a within shaft wich
slides in the outdoors shaft).

Dimensions: 2.5" long when fully compressed.

Requires: Nothing else required

This thing is often bought with the above mentioned thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Here is a wonderful thing that several others have purchased the very same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is exactly what the
guiding knuckles attach to.

FEATURES:
Nylon building, black in color
Stamped right and left to insure proper setup

CONSISTS OF:
2 RPM 30° Front Caster Blocks

REQUIRES:
Assembly in between A-arms and guiding knuckles

The listed below thing also sets really well with the thing being discussed.



This is the ST Racing Silver Aluminum Rear Center Carrier
for the Traxxas Slash 2WD, Stampede, Rustler and Bandit.

FEATURES:
Silver in color

CONSISTS OF:
One Silver Aluminum Rear Center Carrier

Here is a wonderful thing that several others have purchased the very same time.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock containing the shock oil.

FEATURES:
Nylon building

CONSISTS OF:
2 nylon shock cap (tops)
2 nylon shock cap (bottoms)

REQUIRES:
Other shock components

SPECS:
Diameter Tops Bottoms
16MM 13MM

COMMENTS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

Several others have bought this thing together with the thing that you are currently reviewing.

Stub Axle Carriers (2) (R & S)

This is the Traxxas #3652 Stub Axle Carrier that comes consisted of with
the Rustler and Stampede trucks.

FEATURES:
Made of a black plastic/nylon material.
Also called the rear hub or hub carrier.
Has 2 possible install areas for the outer hinge pin shaft.

INCLUDES.
2 Stub alxe carriers.

COMMENTS:
This holds the 2 5x8mm bushings (or bearings) on the stub
axle likewise called the wheel shaft.

AXY
3/25/95

Here is a wonderful thing that several others have purchased the very same time.

Diff Output Yokes Bk (2) W/3X5mm Cntrsnk Screws (2 ) &

These are the Differential Output Yokes
for the Traxxas Outlaw, Stampede and Rustler VXL.

FEATURES:
Black plastic building

CONSISTS OF:
2 differntial output yokes
2 3x5mm countersunk screws
2 screw pins

REQUIRES:
Setup

SPECS:
Length: .70" (18mm)
Diameter: .51" (13mm)