Traxxas Stub Axles Rear (2)

These are the Rear Stub Axles
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal building, black and silver in color

CONSISTS OF:
Two rear stub axles and pins

SPECIFICATIONS:
Length: 1.65" (42mm)
Diameter: .51" (13mm) at biggest point

Below is an additional thing that compliments the thing being talked about.

Half Shafts Long Truck (2)

This is a set of telescoping drive shafts for the Blue Eagle LS II.

Includes: 2 white nylon telescoping shaft (each shaft is made of two pieces)
4 aluminum U-joints

pcd 01/23/94

Below is an additional thing that compliments the thing being talked about.

Half Shafts Long Truck (6)

This is a set of the Traxxas telescoping drive shafts (equivalent of dogbones
or swing shafts). These are for use on Traxxas trucks.

Features: White plastic parts

Consists of:
(6) sets of drive shafts (each set includes a within shaft wich
slides in the outside shaft).

Measurements: 2.5" long when totally compressed.

Requires: Absolutely nothing else required

This thing is frequently acquired with the above mentioned thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a fantastic thing that lots of others have actually bought at the same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs mount to the front A-arms and is what the
steering knuckles connect to.

FEATURES:
Nylon building, black in color
Stamped right and delegated insure appropriate installation

CONSISTS OF:
Two RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and steering knuckles

The below thing additionally pairs really well with the thing being talked about.



This is the ST Racing Silver Aluminum Back Hub Provider
for the Traxxas Slash 2WD, Stampede, Rustler and Bandit.

FEATURES:
Silver in color

CONSISTS OF:
One Silver Aluminum Back Hub Provider

Below is a fantastic thing that lots of others have actually bought at the same time.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock including the shock oil.

FEATURES:
Nylon building

CONSISTS OF:
Two nylon shock cap (tops)
Two nylon shock cap (bottoms)

NEEDS:
Other shock components

SPECIFICATIONS:
Diameter Tops Bottoms
16MM 13MM

COMMENTS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

Many others have actually acquired this thing along with the thing that you are currently checking out.

Stub Axle Carriers (2) (R & S)

This is the Traxxas #3652 Stub Axle Provider that comes included with
the Rustler and Stampede trucks.

FEATURES:
Made of a black plastic/nylon material.
Also called the rear hub or hub carrier.
Has 2 possible mount places for the external hinge pin shaft.

INCLUDES.
2 Stub alxe carriers.

COMMENTS:
This holds the two 5x8mm bushings (or bearings) on the stub
axle also called the wheel shaft.

AXY
3/25/95

Below is a fantastic thing that lots of others have actually bought at the same time.

Diff Output Yokes Bk (2) W/3X5mm Cntrsnk Screws (2 ) &

These are the Differential Output Yokes
for the Traxxas Bandit, Stampede and Rustler VXL.

FEATURES:
Black plastic building

CONSISTS OF:
Two differntial output yokes
Two 3x5mm countersunk screws
Two screw pins

NEEDS:
Installation

SPECIFICATIONS:
Length: .70" (18mm)
Diameter: .51" (13mm)