Traxxas Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a great addition to the thing presently being talked about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Right here is one more thing that praises the thing being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This thing praises the main item below.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These lie in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

INCLUDES:
Two front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

Right here is a terrific thing that numerous others have bought at the very same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This thing is often acquired with the above stated thing.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

REMARKS:
This part fit the requirement and XL version of both the Stampede
and Rustler.

The below thing likewise pairs truly well with the thing being talked about.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Want one more terrific thing to enhance the above stated thing?

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive gear that fits numerous Traxxas
vehicles. .
Includes: 1 gear just

This thing is often acquired with the above stated thing.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler gear

REQUIRES:
Setup on automobile

This thing is often acquired with the above stated thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile