Traxxas Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a fantastic enhancement to the product currently being discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Below is an additional product that praises the product being discussed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This product praises the main item right here.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These lie in the front steering blocks.

FEATURES:
Steel building
Natural color

INCLUDES:
2 front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

Below is a fantastic product that numerous others have bought at the exact same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This product is frequently gotten with the above stated product.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL version of both the Stampede
and Rustler.

The below product also pairs truly well with the product being discussed.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Want an additional fantastic product to enhance the above stated product?

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive equipment that fits several Traxxas
vehicles. .
Consists of: 1 equipment only

This product is frequently gotten with the above stated product.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler equipment

REQUIRES:
Installation on car

This product is frequently gotten with the above stated product.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car