Traxxas Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a amazing enhancement to the product presently being reviewed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Right here is an additional product that compliments the product being reviewed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This product compliments the main item here.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel construction
Natural color

CONSISTS OF:
2 front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

Right here is a terrific product that numerous others have actually bought at the same time.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

This product is often purchased with the above mentioned product.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.

The listed below product likewise pairs truly well with the product being reviewed.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Want an additional terrific product to enhance the above mentioned product?

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits a number of Traxxas
cars. .
Consists of: 1 gear just

This product is often purchased with the above mentioned product.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler gear

REQUIRES:
Installation on car

This product is often purchased with the above mentioned product.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car