Traxxas Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic building
Black in color

INCLUDES:
Two steering obstructs

REQUIRES:
Installation on steering assembly

SPECS:
Length: 35mm (1.38")
Width: 32mm (1.26")

You will certainly enjoy this thing if you have the thing just above mentioned.

Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic building
Black in color

INCLUDES:
One left caster block
One right caster block

REQUIRES:
Installation on Slash

SPECS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

Get this thing to improve the one you read about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Want one more terrific thing to enhance the above pointed out thing?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

INCLUDES:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECS:
Inner Size: 10mm
Outer Size: 15mm
Side Density: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one needed).

Often acquired with the thing that you are currently checking out.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Front driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

Here is one more thing that compliments the thing being gone over.

Stub Axle Housing (2)

These are the axle housings (or center providers) utilized on the: Rad 2, Hawk 2,
Eagle, Blue Eagle LS II and Nitro Rustler. The housings are formed of
black nylon.

Includes: 2 axle housings

pcd 01/23/94

Here is a terrific thing that numerous others have bought at the same time.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

The below thing likewise pairs truly well with the thing being gone over.

Hex Hubs Blue Alum (2) Slash

These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas automobiles
such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits.

FEATURES:
Blue aluminum building

INCLUDES:
Two hex hubs
Four axle pins

REQUIRES:
Assembly onto axles.

SPECS:
Hex Length: 12mm (.47")
Hex Density: 6.1mm (.24")
Axle Pin Length: 9.6mm (.38")

COMMENTS:
These hubs could be utilized with other automobiles making use of the same
    pin/hex design. These hubs Will Not deal with the T-Maxx or E-Maxx.

This thing is frequently acquired with the above pointed out thing.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Hyperlinks
for the Bandit, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
Two rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Installation on the automobile

This thing is frequently acquired with the above pointed out thing.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Hyperlinks
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
Two front 39mm (69mm center to center) turnbuckles and instruction
    sheet

REQUIRES:
Installation on the automobile