Traxxas Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FUNCTIONS:
Composite nylon construction
Replaces a used or damaged bellcrank set
May also be set up on the Traxxas Rustler, Outlaw and 2WD Slash
    designs (assembled in various configurations depending upon design)

CONSISTS OF:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
Two Servo Arms
Two Shoulder Screws
Two 3x15 Counter Sunk Device Screws
Two Hollow Balls
4 Bushings
Guideline Sheet

REQUIRES:
Assembly and installation following the design manual and consisted of
instruction sheet

Right here is a terrific thing that lots of others have bought at the same time.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This thing is frequently gotten with the above pointed out thing.

Extended Fr/Re Body Mounts Slash 2WD

This is the optional Pro-Line Extended Body Mount Package for the
1/10 scale Traxxas Slash 2WD Short Course Trucks.

FEATURES:
Adjustable front and rear body mounts enable a variety of bodies
    to be used including rally vehicle bodies
Constructed of nylon, black in color
Screw-on body mount system gets rid of metal clips

CONSISTS OF:
Front and Rear Body Mounts and Posts with Installing Hardware

The below thing also pairs really well with the thing being gone over.

Waterproof Standard Digital Servo 0.15Sec / 208Oz @ 6V

The SW0231MG is a spending plan friendly waterproof digital servo with fantastic torque for numerous applications. This brushed servo features a speed of .17 and 208.0 oz-in of torque 6.0V. It integrates leading edge technology with extremely high 12-bit (4096) resolution and metal equipments for your greater accuracy when evading puddles. This is a great upgrade if your aiming to drive your RC car in any condition...rain, sleet, or snow.

Functions:

• Integrates cutting edge
  technology with extremely high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Incredibly strong metal equipments make sure long-life and durability.
• Our servos are completely green ? from materials to production, these servos are environmentally friendly.
• Ideal for RC vehicles, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Gear: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Rating: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520

This thing is frequently gotten with the above pointed out thing.

Slash 2Wd Low Cg Chassis Conversion Kit

This is the optional Low CG Conversion Package for the
1/10 scale 2WD Traxxas Slash.

FEATURES:
Reduces the chassis 1" (25.4mm) for much better handling and greater
    cornering speed
Holds battery and electronics as deep in chassis as possible
45% lower battery position

CONSISTS OF:
Chassis
Lower Chassis
Two Nerf Bars
Battery Hold Down with Front and Rear Retainers
Two Front Shock Springs
Hardware and Guidelines

This thing is frequently gotten with the above pointed out thing.

Nerf Bars, For Traxxas Lcg Slash 2Wd, Blue

These are the optional RPM Nerf Bars in Blue for the 2WD Traxxas LCG Slash.

FEATURES:
Engineering grade nylon construction
Replaces the Traxxas #5833, #5833A & #5833G nerf bars
Created specifically for the low center of mass (LCG) Slash
    chassis
Additional cross bracing to optimize rigidity while absorbing impact
    energy

CONSISTS OF:
Left and Right Nerf Bars in Blue