Traxxas Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits several Traxxas
cars. .
Includes: 1 gear just

Frequently acquired with the product that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

Right here is one more product that compliments the product being discussed.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler gear

NEEDS:
Installation on vehicle

The below product likewise pairs truly well with the product being discussed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This product compliments the main item right here.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

This product is often acquired with the above mentioned product.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic main differential

INCLUDES:
Main differential with steel ring gear
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

NEEDS:
Installation on the vehicle

COMMENTS:
For main differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037

You will certainly enjoy this product if you have the product earlier discussed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL version of both the Stampede
and Rustler.

Several others have acquired this product in addition to the product that you are presently reading about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on vehicle

Frequently acquired with the product that you are presently reading about.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This product is often acquired with the above mentioned product.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Designed for designs with a slipper clutch.
Black plastic construction

INCLUDES:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).