Traxxas Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive equipment that fits several Traxxas
automobiles. .
Consists of: 1 equipment only

Often bought with the product that you are currently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

Below is an additional product that praises the product being talked about.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel construction

SUCHES AS:
One steel 30T idler equipment

REQUIRES:
Installation on vehicle

The listed below product likewise pairs actually well with the product being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This product praises the main item here.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

This product is frequently bought with the above discussed product.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

SUCHES AS:
Main differential with steel ring equipment
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Installation on the vehicle

REMARKS:
For primary differential w/ steel ring - TRAC6380
World equipment shafts - TRAC6382
Silicon grease _- TRAC6037

You will enjoy this product if you have the product previously mentioned.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

SUCHES AS:
One gearbox
One idler shaft

REMARKS:
This part fit the standard and XL variation of both the Stampede
and Rustler.

Several others have actually bought this product together with the product that you are currently checking out.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

SUCHES AS:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

Often bought with the product that you are currently checking out.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This product is frequently bought with the above discussed product.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for models with a slipper clutch.
Black plastic construction

SUCHES AS:
One spur equipment

SPECS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).