Traxxas Spur Gear (76T) 48P

This is a 48P, 76T Spur Gear for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
76 tooth
Developed for models with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 76

COMMENTS:
For this slipper clutch design there is also a 86T gear (TRAC4686),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

This is a wonderful addition to the item currently being discussed.

Spur Gear (83T) 48P

This is a 48P, 83T Stimulate Gear for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for models with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    86T gear (TRAC4686) and 90T gear (TRAC4690).

Get this item to boost the one you are reading about.

31T Pinion 48P

This is a 31 Tooth, 48 Pitch Pinion Gear with Set Screw
from Traxxas.

FEATURES:
Steel building and construction, silver in color

CONSISTS OF:
One 31 Tooth, 48 Pitch Pinion Gear
One 3x4mm Set Screw (1.5mm hex size)

REQUIRES:
Setup

SPECS:
Length: .42" (10.5mm)
Inside Diameter: 1/8"
Outside Diameter: .69" (17.5mm)

Lots of others have purchased this item together with the item that you are currently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Below is one more item that praises the item being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

Get this item to boost the one you are reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Want one more fantastic item to compliment the above discussed item?

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
6 black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These might also be referred to as coverplate screws.

This item is frequently purchased with the above discussed item.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Hub

REQUIRES:
Assembly onto Automobile

This item praises the above discussed item.

Traxxas Female Connector Set (2)

These are the Female Traxxas Connectors Plugs Just (No Wires).

FUNCTIONS:
Shrouded wire connections (no shrink tube needed)
Wide surface area, gold-plated terminals
Reverse polarity security makes it difficult to link in reverse
Textured surface area for easy gripping
Suitable with high-current 12-gauge wire
Secure, favorable locking spring crammed terminals for consistent
    contact
Multiple locking barbs keep terminals protect

CONSISTS OF:
Two black female plastic ports
Two sets of gold metal pins
Direction sheet

REQUIRES:
Soldering wires to the metal pins