Traxxas Spring Retainers

These are the Traxxas Spring Retainers for Traxxas Shocks.
This set contains the spring retainers that hold the springs in
place over the shock body and the piston heads that control the amount
of oil circulation in the shock cylinder.

FEATURES:
Constructed of molded plastic.
Contains enough parts for 2 shocks.
Fits the shocks on the majority of Traxxas nitro and electrical powered vehicles.
Two hole piston head for higher dampening or three hole piston head
    for softer spring performance.

INCLUDES:
One Traxxas Spring Retainer Set with:
    2 upper and 2 lower spring retainers
    2 2 hole piston head covers
    Two 3 hole piston head covers

REQUIRES:
Disassembly of shock to install parts.

This product is regularly gotten with the above pointed out product.

Wide Front Bumper, For Traxxas Rustler/Stampede/ Nitro Sport/Ban

This is a Wide Front Bumper for the Traxxas Rustler and Stampede.
The Bumper goes on the Front of the Automobile and Safeguards the Chassis.

FEATURES:
Durable Plastic Building
Black in Color

CONSISTS OF:
One Bumper
One Team RPM Decal

REQUIRES:
Setup onto the Traxxas Rustler or Stampede.

SPECS:
Length: 2-3/4"
Width: 6-1/8"

COMMENTS:
The Factory Number is #81162

This product compliments the main item below.

Shoulder Screws Ultra Shocks

These are the Shoulder Screws for the Traxxas T-Maxx 3.3.

FEATURES:
Black steel building

CONSISTS OF:
Six steel shoulder screws

SPECIFICATIONS:
Length: 12mm
Diameter: 3mm

Right here is an additional product that compliments the product being gone over.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock including the shock oil.

FEATURES:
Nylon building

CONSISTS OF:
2 nylon shock cap (tops)
2 nylon shock cap (bottoms)

REQUIRES:
Other shock elements

SPECIFICATIONS:
Diameter Tops Bottoms
16MM 13MM

COMMENTS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

The listed below product likewise pairs actually well with the product being gone over.

Motor Titan 12T 550 (12-Turns)

    This is the Traxxas Titan 550 12 Turn Electric Motor.

FEATURES:
Stock motor supplied with the Traxxas Stampede and Rustler series
Preinstalled leads, capacitors and ports

CONSISTS OF:
Traxxas Titan 550 Motor, 2 capacitors and 2 leads with ports

REQUIRES:
Installing in vehicle

SPECIFICATIONS:
Can Diameter: 1.25" (38mm)
Shaft Diameter: 0.12" (3mm)
Length Including Shaft: 3.2" (81mm)
Length Not Including Shaft: 2.3" (57.5mm)
Specs such as RPM are not offered

Right here is an additional product that compliments the product being gone over.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for models with a slipper clutch.
Black plastic building

CONSISTS OF:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

Lots of others have gotten this product together with the product that you are presently reading about.

Rod Ends Long & Short

This set of rod ends, balls, and screws is utilized on all but four of Traxxas'
sets. It WILL NOT DEAL WITH: the Sledgehammer, initial Hawk, Feline, or Bullet.

Includes: 4 brief rod ends (17mm)
16 long rod ends (19mm)
2 ball screws
18 hollow ball ports

pcd 01/23/94