Traxxas Shock Tower Front Bandit / Slash / Stampede / Rustler

This is a stock replacement FRONT shock tower for the Traxxas Stampede.

FEATURES:
Made from black molded nylon
For the Traxxas Stampede

SPECS:
Height: 2 3/4"
Density: 1/4"
Width at base: 2 3/4"
Width at top: 2"

INCLUDES:
(1) Front shock tower for the Traxxas Stampede

Many others have actually gotten this product along with the product that you are presently checking out.

Front Bulkhead (Gray) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead utilized in many Traxxas vehicles.
The front suspension arm hinge pins pass through this piece.

FEATURES:
Gray nylon building

INCLUDES:
One front bulkhead

REQUIRES:
Absolutely nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

REMARKS:
This part is utilized on the following cars:
    Rustler, Outlaw, Stampede, Nitro Rustler, SRT, Nitro Stampede,
    Rustler XL and Stampede XL.

Often gotten with the product that you are presently checking out.

Caster Blocks 30 Degree (L&R) Slash / Stampede / Rustler

These are Castor Blocks for the Traxxas
Rustler and Stampede.

FEATURES:
Black Plastic Construction

INCLUDES:
Two Blocks

REQUIRES:
Traxxas Rustler or Stampede

Below is a fantastic product that many others have actually purchased the same time.

Steering Blocks L&R Slash/ Rustler/Stampede/Bandit

These are the Left and Right Guiding Blocks
for the Traxxas Outlaw, Stampede and Rustler VXL series.

FEATURES:
Plastic building
Black in color

INCLUDES:
One left and best steering blocks

REQUIRES:
5x11x4mm bearings (DTXC1547)

This product praises the above gone over product.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

This product praises the main item right here.

Servo Case/Gaskets For 2056 And 2075 Servos

This is the replacement Servo Case and Gasket Set for the Traxxas
2056 - TRAM2026 and 2075 (we don't stock) Servos

FEATURES:
Three piece plastic case molded in blue and black color
Replaces worn or broken servo cases and gaskets

INCLUDES:
One Upper Case (blue plastic)
One Middle Case (blue plastic)
One Lower Case (black plastic)
One Upper Case Gasket
One Lower Case Gasket
One Output Shaft O-Ring
Four Case Screw O-Rings

REQUIRES:
Assembly

This product praises the main item right here.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FEATURES:
Made of stainless-steel
This is utilized to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electric
(not Nitro) Rustler
Also called the vertical kingpin

INCLUDES:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97

This product praises the above gone over product.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock containing the shock oil.

FEATURES:
Nylon building

INCLUDES:
Two nylon shock cap (tops)
Two nylon shock cap (bottoms)

REQUIRES:
Other shock components

SPECS:
Diameter Tops Bottoms
16MM 13MM

REMARKS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

The listed below product additionally sets really well with the product being gone over.

Rod Ends/Ball Connector (6)

These are 5.8mm ball ends and balls use in the LS II race truck kit.

Kit includes: 6ea 5.8mm metal balls
6ea 5.8mm white nylon ball ends

pcd 01/10/94