Traxxas Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

You will love this item if you have the item earlier discussed.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive equipment that fits a number of Traxxas
cars. .
Includes: 1 equipment just

Regularly purchased with the item that you are currently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below item also pairs truly well with the item being discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Want an additional wonderful item to match the above pointed out item?

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler equipment

NEEDS:
Installation on vehicle

Below is an additional item that compliments the item being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Steel Disc
3 Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

Below is an additional item that compliments the item being discussed.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Vehicle

This item is often purchased with the above pointed out item.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for models with a slipper clutch.
Black plastic construction

INCLUDES:
One spur equipment

SPECS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

Below is a wonderful item that lots of others have bought at the exact same time.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide from the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

The listed below item also pairs truly well with the item being discussed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.