Traxxas Servo Connector, Y-Adapter For Dual-Servo Steering Revo

This is the Servo Y Harness for the Dual Steering Servos
for the REVO from Traxxas.

FEATURES:
Futaba J ports (one male to go into the RX and two female to
go to the servos)

INCLUDES:
One Y harness w/two 3" zip ties

NEEDS:
Absolutely nothing

SPECS:
Length: 3" (76mm) approx

This thing is regularly acquired with the above mentioned thing.

Castle Bec 10Amp (25 Volt Max Input)

This is the CC BEC 10A Receiver Battery Remover by Castle Creations.

FEATURES:
Eliminates the need for a receiver and servo battery pack
Draws greater voltage from the motor batteries and drops it to a
    voltage level suitable for the receiver and servos

INCLUDES:
One CC BEC receiver battery eliminator

NEEDS:
Installation in the airplane

SPECS:
Length: 1.2" (30mm)
Width: .6" (15mm)
Height: .4" (10mm)
Weight: .4oz (11g)
Input voltage: 5V to 25.2V (TWO to SIX LiPo)
Present output: 12 volts input = 7 amps* constant, 10 amp peak;
    24 volts input = 5 amps* constant, 7 amp peak
    *Ratings are figured out with a 5mph air flow on the BEC
Selectable Output: 4.8 - 9.0V through the Castle Link (sold separately)
    Default voltage is 5.1V

The listed below thing also pairs truly well with the thing being talked about.



These are the EMS Unassembled Female Radio System Connectors.

FEATURES:
Suitable with Hitec, Airtronics Z and JR systems
Allows modelers to custom make their own extensions, servo leads,
    battery leads and more
Gold plated for high conductivity and reliability
Fits wire sizes from 20 to 30 AWG
No soldering needed
Two year restricted service warranty

INCLUDES:
15 pins, 5 inner male ports and 5 female shells,
    and instruction sheet

NEEDS:
Servo wire (HRCM3001)
Wire crimping tool

REMARKS:
For the Male Connectors, order EMOM0017

This thing is regularly acquired with the above mentioned thing.

King Off-Rd Pggybck Shocks w/Faux Reservoir 100

This is a set of King Off-Road 100mm Racing Shocks w/Faux Tank from RC4WD

FUNCTIONS:
Machined billet aluminum building
Dual spring design
King logo on synthetic piggyback and retainer ring

INCLUDES:
Two 1/10 scale King Off-Road 110mm Racing Shocks w/Faux Tank

SPECS:
Hole to Hole (Compressed): 2.75" (70mm)
Hole to Hole (Uncompressed): 3.93" (100mm)
Overall Length: 4.28" (108.9mm)
Travel Length: 1.18" (30mm)
Shock Body OD: 0.39" (10mm)
Spring Body OD: 0.57" (14.5mm)
Shaft Size: 0.17" (3.5mm)
Weight: 0.9oz (26g)

REMARKS:
King Off-Road is a signed up trademark of the King Off-Road Shock
    company. The King Off-Road logo is home of King Off-Road
    Shocks.

This thing is regularly acquired with the above mentioned thing.

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older style cases utilized on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

INCLUDES:
Fan with Wire Lead and Adapter
Fan Shroud

SPECS:
Input Voltage: 4.8 - 7.4V
Optimum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, remove before exposing ESC to moisture