Traxxas Sealed Receiver Box (Slash)

This is the Receiver Box for the 2WD Traxxas Slash Truck.

FEATURES:
Replaces broken receiver boxes
Constructed of black plastic

CONSISTS OF:
One top and bottom half receiver box for the Traxxas Slash
Hardware

NEEDS:
Setting up receiver and bolting receiver box to chassis.

Want one more wonderful item to compliment the above discussed item?

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Fully put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Connects to the differential with one screw pin
Works on the front or back, right or left of vehicle

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

NEEDS:
Setting up on chassis

This item is frequently gotten with the above discussed item.

Pivot Ball Caps & Dust Boots

This is the replacement Pivot Ball and Dust Cap Boot Set
    for the Traxxas Revo, E-Revo and T-Maxx 3.3 vehicles.

FEATURES:
Nylon and Rubber Construction
Blue and Black in Color

CONSISTS OF:
4 Blue Rubber Pivot Ball Boots
4 Black Dust Boot Retainer
4 Blue Notched Dust Boot Retainer
4 Blue Rubber Boot Plugs
4 nylon Pivot Ball Retainers
Guideline sheet

NEEDS:
Two plans needed to finish truck

This item is frequently gotten with the above discussed item.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Advised for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) ready to run (not for usage in much heavier
    cars such as E-Revos or E-Maxx class cars)
USB shows capability through Castle Link USB adapter (not consisted of,
    order CSEM6300)
Water resistant for usage in nearly every environment (not meant for
    operation while submerged in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can replaces lots of stock brushed motors
4 magnet, 4 pole rotor for greater torque
1.4" size slotted stator
Detachable end bell

CONSISTS OF:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Port,
    On/Off Switch, Directions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

NEEDS:
Battery port of modeler's option

SPECIFICATIONS:
ESC;
Input Voltage: 2S LiPo minimum, THREE LiPo maximum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Measurements: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery port
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Port: 4mm gold
Wire Length: 9.5" (241mm)