Traxxas Rod Ends Revo Large W/ Hollow Balls

This is the Big Rod End Set for the Traxxas Revo.

FEATURES:
Plastic building and construction
Black in color
Metal Pivot Balls

CONSISTS OF:
12 Rod Ends
12 Pivot Balls

NEEDS:
Assembly to automobile

SPECIFICATIONS:
Length: 22mm (.88")
Width at ball joint: 10mm (.39")

Often bought with the product that you are currently reviewing.

Toe Link 5.0Mm Steel Frnt Or Rr (2) Revo

This is a set of replacement Toe Hyperlinks for the Traxxas Revo Truck.
    These change the position of the toe on the vehicle.

FEATURES:
Steel turnbuckle design
5.0mm diameter

CONSISTS OF:
Two front or rear toe links

NEEDS:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 5.1" (129mm)

Want one more wonderful product to compliment the above pointed out product?

Turnbuckles Toe Links Rr 5Mm (

These are the Rear Turnbuckles/Toe Hyperlinks for the Traxxas 3.3 T-Maxx, TRAC78**.

FEATURES:
Constructed of steel, refined natural finish

CONSISTS OF:
Two Rear Turnbuckles/Toe Hyperlinks for the Traxxas 3.3 T-Maxx.

NEEDS:
Setting up between wheel hubs and rear bulkheads

SPECIFICATIONS:
Length: 4.9" (125mm)
Size: 0.20" (5mm)

REMARKS:
Fits just the 3.3 variation of the T-Maxx.

Want one more wonderful product to compliment the above pointed out product?

Front Bumper Slayer

This is the Front Bumper and Mount for the
    Traxxas Slayer Pro 4WD Short Course Nitro RTR

FEATURES:
Nylon building and construction
Black in color

CONSISTS OF:
One Front Bumper
One Bumper Mount
Two 3x25mm Button Cap Screws
Two 4x10mm Button Cap Screws

NEEDS:
Installation on the automobile

Below is a wonderful product that many others have purchased the very same time.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a wonderful product that many others have purchased the very same time.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

CONSISTS OF:
Two Ball Bearings

NEEDS:
Assembly to automobile

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are utilized to support the Primary Clutch (one required).

This product is often bought with the above pointed out product.

Rod Ends (12) / Hollow Balls (12) Jato

    These are the Rod Ends and Balls for the Traxxas Jato.

FEATURES:
Black nylon construction.
Steel hollow balls.

INCLUDES:
Twelve rod end/balls

NEEDS:
Setting up on Jato

SPECIFICATIONS:
Length: 1-1/8" (28mm)
Width: 3/8" (9mm)

The listed below product additionally pairs actually well with the product being discussed.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Hyperlinks
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Assembled w/Rod Ends

CONSISTS OF:
Two front 39mm (69mm center to center) turnbuckles and direction
    sheet

NEEDS:
Installation on the automobile

This product is often bought with the above pointed out product.



This is a optional Racers Edge Aluminum single arm servo horn, meant for use with Futaba servos. This sturdy aluminum servo horn is comparable in design to the Racers Edge Pro Adjustable servo horns, however includes a third linkage installing point and does not use lock down screws.