Traxxas Rod Ends Revo Large W/ Hollow Balls

This is the Big Rod End Set for the Traxxas Revo.

FEATURES:
Plastic building
Black in color
Metal Pivot Balls

CONSISTS OF:
12 Rod Ends
12 Pivot Balls

REQUIRES:
Assembly to automobile

SPECS:
Length: 22mm (.88")
Width at ball joint: 10mm (.39")

Regularly gotten with the item that you are currently reading about.

Toe Link 5.0Mm Steel Frnt Or Rr (2) Revo

This is a set of replacement Toe Links for the Traxxas Revo Truck.
    These adjust the position of the toe on the vehicle.

FEATURES:
Steel turnbuckle design
5.0mm size

CONSISTS OF:
Two front or rear toe links

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 5.1" (129mm)

Want another terrific item to match the above mentioned item?

Turnbuckles Toe Links Rr 5Mm (

These are the Rear Turnbuckles/Toe Links for the Traxxas 3.3 T-Maxx, TRAC78**.

FUNCTIONS:
Constructed of steel, refined natural finish

CONSISTS OF:
Two Rear Turnbuckles/Toe Links for the Traxxas 3.3 T-Maxx.

REQUIRES:
Setting up between wheel centers and rear bulkheads

SPECS:
Length: 4.9" (125mm)
Diameter: 0.20" (5mm)

REMARKS:
Fits only the 3.3 version of the T-Maxx.

Want another terrific item to match the above mentioned item?

Front Bumper Slayer

This is the Front Bumper and Mount for the
    Traxxas Slayer Pro 4WD Short Course Nitro RTR

FUNCTIONS:
Nylon building
Black in color

CONSISTS OF:
One Front Bumper
One Bumper Mount
Two 3x25mm Button Cap Screws
Two 4x10mm Button Cap Screws

REQUIRES:
Installation on the automobile

Here is a terrific item that lots of others have purchased the exact same time.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Here is a terrific item that lots of others have purchased the exact same time.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one needed).

This item is regularly gotten with the above mentioned item.

Rod Ends (12) / Hollow Balls (12) Jato

    These are the Rod Ends and Balls for the Traxxas Jato.

FEATURES:
Black nylon construction.
Steel hollow balls.

INCLUDES:
Twelve rod end/balls

REQUIRES:
Setting up on Jato

SPECS:
Length: 1-1/8" (28mm)
Width: 3/8" (9mm)

The below item also sets truly well with the item being reviewed.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
Two front 39mm (69mm center to center) turnbuckles and direction
    sheet

REQUIRES:
Installation on the automobile

This item is regularly gotten with the above mentioned item.



This is a optional Racers Edge Aluminum single arm servo horn, intended for usage with Futaba servos. This heavy duty aluminum servo horn is comparable in design to the Racers Edge Pro Adjustable servo horns, but features a third linkage mounting point and does not use lock down screws.