Traxxas Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic main differential

CONSISTS OF:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the car

REMARKS:
For main differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037

Many others have actually bought this product in addition to the product that you are currently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This product is often bought with the above stated product.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler gear

NEEDS:
Setup on car

Want an additional terrific product to compliment the above stated product?

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits numerous Traxxas
vehicles. .
Consists of: 1 gear just

This is a fantastic addition to the product currently being gone over.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on car

The listed below product also sets actually well with the product being gone over.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

REMARKS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.

The listed below product also sets actually well with the product being gone over.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Many others have actually bought this product in addition to the product that you are currently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Many others have actually bought this product in addition to the product that you are currently reviewing.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Light weight carbon fiber composite transmission case
Longer motor installing slots for more gear ratio combinations
CNC 6061 aluminum motor plate, heat sink and arm install
Bigger open location for a bigger motor heat sink
Thirty day limited warranty starting at date of purchase-valid
    in the United States just

CONSISTS OF:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Many others have actually bought this product in addition to the product that you are currently reviewing.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs install to the front A-arms and is what the
guiding knuckles connect to.

FEATURES:
Nylon construction, black in color
Stamped right and left to guarantee right installation

CONSISTS OF:
Two RPM 30° Front Caster Blocks

NEEDS:
Assembly between A-arms and guiding knuckles