Traxxas Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the automobile

COMMENTS:
For primary differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037

Many others have gotten this product in addition to the product that you are presently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This product is regularly gotten with the above mentioned product.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for many Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler equipment

NEEDS:
Setup on automobile

Want another excellent product to enhance the above mentioned product?

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive equipment that fits numerous Traxxas
vehicles. .
Includes: 1 equipment just

This is a wonderful enhancement to the product presently being gone over.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

The listed below product additionally pairs really well with the product being gone over.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.

The listed below product additionally pairs really well with the product being gone over.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Many others have gotten this product in addition to the product that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Many others have gotten this product in addition to the product that you are presently reviewing.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Equipment Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Lightweight carbon fiber composite transmission case
Longer motor mounting slots for more equipment ratio combinations
CNC 6061 aluminum motor plate, heat sink and arm mount
Larger open area for a larger motor heat sink
Thirty day minimal service warranty starting at date of purchase-valid
    in the United States just

INCLUDES:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Many others have gotten this product in addition to the product that you are presently reviewing.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs mount to the front A-arms and is what the
guiding knuckles attach to.

FEATURES:
Nylon building and construction, black in color
Stamped right and left to guarantee correct setup

INCLUDES:
Two RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and guiding knuckles