Traxxas Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Installation on the automobile

REMARKS:
For primary differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037

Several others have purchased this item along with the item that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This item is often purchased with the above mentioned item.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for many Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Installation on automobile

Want another fantastic item to enhance the above mentioned item?

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive equipment that fits several Traxxas
automobiles. .
Consists of: 1 equipment only

This is a wonderful addition to the item presently being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on automobile

The listed below item additionally sets actually well with the item being talked about.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

REMARKS:
This part fit the requirement and XL version of both the Stampede
and Rustler.

The listed below item additionally sets actually well with the item being talked about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Several others have purchased this item along with the item that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

Several others have purchased this item along with the item that you are presently checking out.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Equipment Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Light weight carbon fiber composite transmission case
Longer motor mounting slots for more equipment ratio combinations
CNC 6061 aluminum motor plate, heat sink and arm mount
Bigger open area for a larger motor heat sink
Thirty day restricted service warranty starting at date of purchase-valid
    in the United States only

CONSISTS OF:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Several others have purchased this item along with the item that you are presently checking out.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks mount to the front A-arms and is what the
guiding knuckles attach to.

FEATURES:
Nylon building and construction, black in color
Stamped right and delegated guarantee right setup

CONSISTS OF:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly between A-arms and guiding knuckles