Traxxas Planet Gears & Shafts

These are the replacement planetary gear and shafts for the Rad 2 and Hawk 2.

FEATURES:
All these gears and shafts are made of metal(probably with a low
amount of steel).

INCLUDES:
4- planetary gears
4- planteary gear shafts
2- sun gears
1- sun gear alignment shaft

WAJ
1/16/94

Get this product to boost the one you are reading about.

Sealed Aluminum Differential Case For Traxxas 2Wd Electric

This is the optional Hot-Racing Aluminum Differential Case
for the Traxxas Bandit, Rustler, 2WD Stampede, 2WD Slash
and Monster Jam Cars

FEATURES:
CNC aluminum building and construction diff case, black in color
Hardened steel gear
Sealed differentials enables tuning to track conditions by altering
    weight of diff oil
Four O-rings help seal versus fluid leak
Thirty day limited service warranty beginning at date of purchase- valid
    in the United States just

INCLUDES:
Sealed Differential Case
Four O-Rings
Two Screws

SPECS:
Outdoors Diameter: 1.48" (37.5mm)
Shaft Diameter: .200" (5.10mm)
Total Thickness: 0834" (21.2mm)

Numerous others have acquired this product in addition to the product that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

Here is an additional product that compliments the product being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

You will enjoy this product if you have the product above discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

This product is often acquired with the above mentioned product.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Light weight carbon fiber composite transmission case
Longer motor mounting slots for more gear ratio mixes
CNC 6061 aluminum motor plate, heat sink and arm install
Larger open location for a larger motor heat sink
Thirty day limited service warranty beginning at date of purchase-valid
    in the United States just

INCLUDES:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Often acquired with the product that you are presently reviewing.

Main Diff W/ Steel Ring Gear/ Side Cover Plate/ Sc Rews (Ban

This is the Main Diff with Steel Ring Gear from Traxxas
for the Bandit, Stampede and Rustler VXL series.

Includes: Main diff with steel ring gear
Side cover plate
Screws
Instructions

Needs: Installation on the vehicle

Numerous others have acquired this product in addition to the product that you are presently reviewing.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive gear that fits numerous Traxxas
automobiles. .
Consists of: 1 gear just