Traxxas Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Center Set for the Traxxas Rustler and
Stampede. These parts have more offset than
the stock hex wheel center set (TRAC6044).

FEATURES:
Gray plastic construction

CONSISTS OF:
Two wheel hubs
Two 2.5mmX12mm axle pins

SPECS:
Hex size: 12mm
Width: .32" (8mm)

Right here is a terrific product that numerous others have actually bought at the same time.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Lots of others have actually purchased this product in addition to the product that you are presently checking out.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

CONSISTS OF:
Two front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

This is a amazing addition to the product presently being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly love this item if you have the item above mentioned.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

Right here is one more product that praises the product being talked about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

This product praises the above talked about product.

Steering Blocks L&R Slash/ Rustler/Stampede/Bandit

These are the Left and Right Steering Blocks
for the Traxxas Bandit, Stampede and Rustler VXL series.

FEATURES:
Plastic construction
Black in color

CONSISTS OF:
One left and best steering obstructs

REQUIRES:
5x11x4mm bearings (DTXC1547)

Lots of others have actually purchased this product in addition to the product that you are presently checking out.

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated construction

CONSISTS OF:
Eiqht 4mm flanged nylon locking nuts

SPECS:
Outside diameter: 7mm

Right here is one more product that praises the product being talked about.

Oilite Bushings 5X11mm

This is a replacement bushing set for the TRAXXAS TRX-10 BULLET, HAWK2, and
different other TRAXXAS SETS. .
FEATURES:
Made from metal

CONSISTS OF:
14 bushings

SPECS:
5x11mm bushings

REMARKS:
These bushings would work on any automobile using 5x11mm bushings.

This product praises the main item here.

Large Servo Saver

This is a big servo saver that can be used in Traxxas cars or any vehicle that
requires a big style servo saver.
FEATURES:
Difficult white plastic construction.
INCLUDES:
1 large servo saver and 3 adaptors that permit you to install the saver
on a lot of popular servos including: Futaba, Hobbico, Tower, Airtronics,
and Traxxas. Also consisted of is a mounting screw.
SPECIFICATIONS:
Length: 1-3/8"
Diameter: 1"
The servo saver has 6 holes for installing the guiding linkages.