Traxxas Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

SUCHES AS:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.

This item compliments the above talked about item.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Numerous others have gotten this item in addition to the item that you are currently reading about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Here is another item that compliments the item being talked about.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic main differential

SUCHES AS:
Main differential with steel ring gear
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Setup on the automobile

COMMENTS:
For main differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037

This item compliments the main item right here.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

The listed below item likewise pairs actually well with the item being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

SUCHES AS:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

This is a wonderful addition to the item currently being talked about.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits several Traxxas
vehicles. .
Consists of: 1 gear just

You will love this thing if you have the thing just above pointed out.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel building

SUCHES AS:
One steel 30T idler gear

REQUIRES:
Setup on automobile

Want another great item to enhance the above stated item?

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a wonderful addition to the item currently being talked about.

Dust Cover/ Rubber Plug

This is a Dust Cover and Rubber Plug
for the Traxxas Rustler/Stampede

FEATURES:
Made from black molded nylon
For the Traxxas Rustler/Stampede

SUCHES AS:
Dust cover for the Traxxa Rustler
3 x 6 mm round head coarse thread screws (to mount dust cover)
Rubber Plug

Specs: 3" (77mm)
Suitable with Traxxas Telemetry