Traxxas Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

SUCHES AS:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL variation of both the Stampede
and Rustler.

This item compliments the above discussed item.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Lots of others have gotten this item along with the item that you are currently checking out.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Right here is an additional item that compliments the item being discussed.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic main differential

SUCHES AS:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

REQUIRES:
Setup on the automobile

COMMENTS:
For main differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037

This item compliments the main item right here.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

The below item also pairs truly well with the item being discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

SUCHES AS:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

This is a great enhancement to the item currently being discussed.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive gear that fits numerous Traxxas
cars. .
Consists of: 1 gear only

You will certainly love this item if you have the item just above stated.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel construction

SUCHES AS:
One steel 30T idler gear

REQUIRES:
Setup on automobile

Want an additional fantastic item to compliment the above mentioned item?

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a great enhancement to the item currently being discussed.

Dust Cover/ Rubber Plug

This is a Dust Cover and Rubber Plug
for the Traxxas Rustler/Stampede

FUNCTIONS:
Made from black molded nylon
For the Traxxas Rustler/Stampede

SUCHES AS:
Dust cover for the Traxxa Rustler
3 x 6 mm round head coarse thread screws (to install dust cover)
Rubber Plug

Specs: 3" (77mm)
Suitable with Traxxas Telemetry