Traxxas Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These lie in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

INCLUDES:
2 front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

This is a fantastic addition to the item presently being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Regularly acquired with the item that you are presently checking out.

Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Hub Set for the Traxxas Rustler and
Stampede. These parts have more offset than
the stock hex wheel hub set (TRAC6044).

FEATURES:
Gray plastic building and construction

INCLUDES:
2 wheel centers
2 2.5mmX12mm axle pins

SPECIFICATIONS:
Hex size: 12mm
Width: .32" (8mm)

The listed below item also pairs really well with the item being gone over.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This item is often acquired with the above pointed out item.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Regularly acquired with the item that you are presently checking out.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This is a fantastic addition to the item presently being gone over.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Below is one more item that compliments the item being gone over.

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building and construction

INCLUDES:
Eiqht 4mm flanged nylon locking nuts

SPECIFICATIONS:
Outdoors diameter: 7mm

This item compliments the main item right here.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FEATURES:
Made from stainless steel
This is utilized to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electrical
(not Nitro) Rustler
Also called the vertical kingpin

INCLUDES:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97

Below is a fantastic item that many others have actually bought at the same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is what the
steering knuckles connect to.

FEATURES:
Nylon building and construction, black in color
Stamped right and left to insure correct installation

INCLUDES:
2 RPM 30° Front Caster Blocks

REQUIRES:
Assembly between A-arms and steering knuckles