Traxxas Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These lie in the front steering blocks.

FEATURES:
Steel building
Natural color

INCLUDES:
2 front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

This is a fantastic addition to the item presently being reviewed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Often bought with the item that you are presently checking out.

Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Center Set for the Traxxas Rustler and
Stampede. These parts have more offset than
the stock hex wheel hub set (TRAC6044).

FUNCTIONS:
Gray plastic building

INCLUDES:
2 wheel hubs
2 2.5mmX12mm axle pins

SPECIFICATIONS:
Hex size: 12mm
Width: .32" (8mm)

The below item likewise sets actually well with the item being reviewed.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This item is often bought with the above stated item.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Often bought with the item that you are presently checking out.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This is a fantastic addition to the item presently being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

Below is one more item that praises the item being reviewed.

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building

INCLUDES:
Eiqht 4mm flanged nylon locking nuts

SPECIFICATIONS:
Outdoors diameter: 7mm

This item praises the main item here.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FUNCTIONS:
Made of stainless-steel
This is utilized to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electrical
(not Nitro) Rustler
Also called the vertical kingpin

INCLUDES:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97

Below is a fantastic item that numerous others have bought at the exact same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks mount to the front A-arms and is what the
steering knuckles connect to.

FEATURES:
Nylon building, black in color
Stamped right and left to insure appropriate setup

INCLUDES:
2 RPM 30° Front Caster Blocks

REQUIRES:
Assembly in between A-arms and steering knuckles