Traxxas Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel construction
Natural color

INCLUDES:
2 front axles

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

This is a fantastic addition to the thing presently being discussed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Often purchased with the thing that you are presently reading about.

Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Center Set for the Traxxas Rustler and
Stampede. These parts have more balanced out than
the stock hex wheel hub set (TRAC6044).

FEATURES:
Gray plastic construction

INCLUDES:
2 wheel centers
2 2.5mmX12mm axle pins

SPECIFICATIONS:
Hex size: 12mm
Width: .32" (8mm)

The below thing likewise pairs actually well with the thing being discussed.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This thing is often purchased with the above pointed out thing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Often purchased with the thing that you are presently reading about.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This is a fantastic addition to the thing presently being discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on vehicle

Right here is another thing that praises the thing being discussed.

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated construction

INCLUDES:
Eiqht 4mm flanged nylon locking nuts

SPECIFICATIONS:
Outdoors size: 7mm

This thing praises the main item here.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FEATURES:
Made of stainless-steel
This is used to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electric
(not Nitro) Rustler
Also called the vertical kingpin

INCLUDES:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97

Right here is a great thing that several others have bought at the same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs mount to the front A-arms and is exactly what the
steering knuckles attach to.

FEATURES:
Nylon construction, black in color
Stamped right and delegated guarantee correct installation

INCLUDES:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and steering knuckles