Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For usage in all Traxxas TRX2.5 and TRX 3.3 equipped cars
Pull starter can be eliminated to install the EZ Start
60% more peak power than the TRX2.5, with nearly 50% more power
    under the curve for strong linear velocity
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Starter and radiance plug
One direction handbook (TRAZ5300)
One service assistance guide and parts lis.
One set of engine decals
One engine break-in DVD
One little bottle of air filter oil
One air filter

NEEDS:
Car fuel with 10%, 20% or 33% nitro content

SPECIFICATIONS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance in between mounting holes very same side: 0.39" (10mm)
Distance in between mounting holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of mounting flanges/top of cylinder head: 3.5" (88mm
Width of mounting flanges: 44mm

REMARKS:
Other versions of the TRX 3.3 engine consist of;
    #5404 Single Shaft without Starter, TRAG5404
    #5406 Multi-Shaft without Starter, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Starter, TRAG5409

Right here is one more product that praises the product being talked about.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Requirement Connector.

FEATURES:
Suitable sport pack for cars, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Conventional
    Adapter

NEEDS:
NiMH suitable charger such as the Duratrax Onyx series

SPECIFICATIONS:
Capability: 3000mAh
Variety of Cells in Series: 6
Rated Voltage: 7.2V
Minutes. Discharge Voltage: 5.4V
Optimum Recommended Charge Current: 4 amps
Discharge Lead: 14AWG 2.7" (70mm) long wire w/Standard connector
Load Dimensions: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This product praises the main item below.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

BUNDLE
CONSISTS OF:
1-Beveled Cone

FUNCTIONS:
Black steel construction
Beveled cone shape with split on one side

REMARKS:
Beveled cone sits in front of the flywheel
7/19/94sk

Many others have purchased this product in addition to the product that you are currently reading about.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It allows you to mount the newer 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipe, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

CONSISTS OF:
One Plastic Tune Pipe w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carb Link Bellcrank (TRAC5167)
One Slide Carb Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post mounting holes
Two Tie-Straps for mounting Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm device cap screw w/washer
One direction sheet
One drilling template sheet

NEEDS:
2.5 engine stock clutch system and stock engine mount

SPECIFICATIONS:
Tune Pipe Length: 101.6mm (4")
Header Pipe Outer Diameter: 13mm (.51")
Drill Bit size: 3.175mm (.125")

REMARKS:
If EZ Start system is needed, use TRAP5271