Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For use in all Traxxas TRX2.5 and TRX 3.3 equipped cars
Pull starter can be eliminated to set up the EZ Start
60% more peak power than the TRX2.5, with almost 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Starter and glow plug
One guideline handbook (TRAZ5300)
One service assistance guide and parts lis.
One set of engine decals
One engine break-in DVD
One small bottle of air filter oil
One air filter

NEEDS:
Car fuel with 10%, 20% or 33% nitro content

SPECIFICATIONS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance between installing holes same side: 0.39" (10mm)
Distance between installing holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of installing flanges/top of cylinder head: 3.5" (88mm
Width of installing flanges: 44mm

COMMENTS:
Other variations of the TRX 3.3 engine consist of;
    #5404 Single Shaft without Starter, TRAG5404
    #5406 Multi-Shaft without Starter, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Starter, TRAG5409

Here is one more thing that compliments the thing being reviewed.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Requirement Connector.

FEATURES:
Perfect sport pack for cars, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Standard
    Adapter

NEEDS:
NiMH suitable charger such as the Duratrax Onyx series

SPECIFICATIONS:
Capability: 3000mAh
Number of Cells in Series: 6
Rated Voltage: 7.2V
Minutes. Release Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Release Lead: 14AWG 2.7" (70mm) long wire w/Standard port
Load Dimensions: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This thing compliments the main item below.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PLAN
CONSISTS OF:
1-Diagonal Cone

FUNCTIONS:
Black steel building and construction
Diagonal cone shape with split on one side

COMMENTS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Several others have actually acquired this thing together with the thing that you are presently reviewing.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It allows you to mount the newer 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipe, bellcrank, & throttle servo horn made of plastic
Linkage wire made of steel

CONSISTS OF:
One Plastic Tune Pipe w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carb Link Bellcrank (TRAC5167)
One Slide Carb Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post installing holes
Two Tie-Straps for installing Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm device cap screw w/washer
One guideline sheet
One drilling template sheet

NEEDS:
2.5 engine stock clutch system and stock engine mount

SPECIFICATIONS:
Tune Pipe Length: 101.6mm (4")
Header Pipe Outer Size: 13mm (.51")
Drill Bit size: 3.175mm (.125")

COMMENTS:
If EZ Start system is needed, utilize TRAP5271